Текст страницы
•
If summer is very dry, do not scarify in autumn.
Usage
Height
•
Scarifying
Raking
(Optional accessory)
•
+5mm
Tips for raking:
Plenty amount of air is needed for the area around the
roots of the lawn in order to maintain healthy growth in
spring season.
It is recommended performing aeration operation on the
lawn every 4 – 6 weeks in accordance with the state of
the lawn.
For transportation and
storage.
Raking normal lawn.
For transportation and
storage.
Scarifying sensitive lawn.
Dethatching thin layers.
The second scarifying
operation in autumn.
MAINTENANCE
0mm
Scarifying normal lawn.
Dethatching normal layer.
Raking rough thick lawn.
•
-5mm
Scarifying normal lawn.
Dethatching thick layer.
Do NOT use for raking
operation.
•
Do NOT use for raking
operation.
•
-10mm
Scarifying rough thick
lawn.
Dethatching thick layer.
•
Changing the height
Push the height adjustment lever (12) outward, and move
it to desired position.
•
•
•
CAUTION:
Always be sure that the machine is switched off
and unplugged before performing inspection or
maintenance.
Wear protective gloves before performing inspection or
maintenance.
The cutter does not stop immediately after switch off.
Wait until all the parts stop before performing any
maintenance work.
Make sure that all the tools are removed after
maintenance work.
Never use gasoline, benzine, thinner, alcohol or the like
for cleaning. Discoloration, deformation or cracks may
result. To clean the machine, use only moist cloth and
soft brush.
Do not hose or clean the machine with high pressured
water.
•
Overload protection
This machine is equipped with overload protection, and it
functions under the following situations:
The cutting tool becomes clogged because scarified
materials are built up around it.
The machine is trying to scarify more than the motor
can handle.
Something hinders the rotation of the cutting tool.
•
•
•
When this protection works, the machine is switched off
automatically.
If it happens, unplug the machine, wait until it cools down,
and remove the cause of the overload before restarting
the machine.
•
•
•
When transporting the machine, pay attention to the
following points:
Switch off the motor, unplug and wait until the cutting
tool stops.
Adjust the depth of the cutting tool to transportation
height.
Always transport the machine by its handle.
Avoid heavy impact or strong vibration.
Secure the machine firmly in case it is embarked on
vehicles.
OPERATION
•
•
Perform the following steps after each operation:
Switch off the motor, unplug and wait until the cutting
tool stops.
Clean the grass catcher. Store it in a dry room.
Check, clean and store the machine in a dry room.
•
•
•
•
•
•
•
•
•
•
•
•
•
Operation Tips:
Cut your grass before operation and fertilize after the
operation.
Adjust the depth of the cutting tool in accordance with
the height of the grass and weather.
Avoid operating on wet grass. It tends to stick on the
discharge port and other parts of the machine. It may
also cause slip and fall.
Do not move too fast. Push the machine slowly.
Otherwise discharge port may become clogged and the
motor may overloaded.
Operate along a line as straight as possible.
Make slightly overlapping scarified lines. It will maintain
even and smooth surface.
When a flower bed is included in the operating area,
make a circle or two around the flower bed.
Be especially careful when turning the machine.
Do not stay in one position. It damages the grass.
•
•
Perform the following work at regular basis:
Check all the clamps, such as screws, nuts etc. are
tightly fasten.
Check for defects such as loose, worn, or damaged
parts. Replace them if necessary.
Check that the covers and guards are not damaged or
deformed.
If the machine starts vibrating abnormally during
operation, that may be caused by unbalanced or
deformed cutting tool due to the impacts by foreign
objects. Have the cutting tool repaired or replaced by
authorized service center if it happens.
The cutting tool is worn out during the course of time.
Check the condition of the cutting tool and its stability on
regular basis. Replace it if it is worn or become blunt.
Clean and lubricate all screw parts before storage.
•
•
•
•
•
Tips for scarifying:
Always take the weather into account. Warm, sunny
and wet weather is good for scarifying because the
lawn can recover healthily. On the other hand, avoid
cold, heat, dry weather.
During spring season scarify the lawn.
If summer is wet, scarify the lawn in early autumn.
Refrain from scarifying during period of extremely hot
weather.