Текст страницы
English | 15
u Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
u Switch the power tool off immediately if the applica-
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
u Apply pressure only in direct line with the bit and do
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Product Description and
Specifications
u Hold the power tool securely. When tightening and
loosening screws be prepared for temporarily high torque
reactions.
u Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
u Use suitable detectors to determine if there are hid-
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
The power tool is intended for driving and loosening screws
and for drilling in wood, metal, ceramic and plastic. The GSB
cordless combi drill is also designed for impact drilling in
brick, masonry and stone.
u Always wait until the power tool has come to a com-
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
u In case of damage and improper use of the battery, va-
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
u Do not open the battery. There is a risk of short-circuit-
ing.
u The battery can be damaged by pointed objects such
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
(1)
Tool holder
(2)
Keyless chuck
(3)
Torque presetting ring
(4)
Operating mode presetting ring
(GSB 185-LI)
(5)
Gear selector switch
(6)
Rechargeable batterya)
(7)
Battery release buttona)
u Only use the battery with products from the manufac-
turer. This is the only way in which you can protect the
battery against dangerous overload.
(8)
Worklight (LED)
(9)
Rotational direction switch
(10) On/off switch
(11) Handle (insulated gripping surface)
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless Drill/Driver
GSR 185-LI
GSB 185-LI
Article number
3 601 JK3 0..
3 601 JK3 1..
Rated voltage
V=
18
18
No-load speedA)
– First gear
min-1
0–500
0–500
– Second gear
min-1
0–1 900
0–1 900
Impact rateA)
min-1
–
0–27 000
Max. torque (soft)A)
Nm
21
21
Max. torque (hard)A)
Nm
50
50
Bosch Power Tools
1 609 92A 892 | (13.09.2022)
https://tm.by
Интернет-магазин