Текст страницы
- Place the kettle on a smooth level surface. Do not place the kettle at the edge
of a table.
- Connect the kettle to an electric socket. Excessive power cord can be wrapped
around the guides inside the base and draw its end through the cutout in its side.
- Do not let the power cord hang from a table where a child can pull on it.
- Do not place the kettle near heating appliances and hot surfaces.
- Operate carefully when pouring the water from your kettle as boiling
water may result in scald, besides, don’t open the lid while the water in the
kettle is hot.
- The kettle will not re-boil until the switch is pressed again. The kettle may be
stored on the power base when not in use.
- Always disconnect the power supply when not use.
- Note that you can stop the kettle boiling or keep warm process at any time by
pressing the «ПУСК/ОТМЕНА» (START/CANCEL) button
- Should you lift the kettle from its base during a functions cycle and place it
back on to the base the kettle will enter standby mode and not resume the
pre-selected function cycle. The screen will display the real temperature of the
water on the digital tube. Please do not add water into the kettle during a
boiling or keep warm cycle. Always ensure to remove the kettle from the base
before pouring.
- When the water has boiled (without using the keep warm cycle) the kettle will
enter standby mode and its display will turn off approximately 30 seconds. To
wake the appliance, press any button.
- Using the «+» «-» key, you can choose the temperature what you want, but after
choose the temperature, you need press the «ПУСК/ОТМЕНА» (START/CANCEL) key
to start the kettle, otherwise, the kettle will not start working. «+» key can add the
temperature only, «-» key can subtract the temperature only.
the 40, 60 ⁰С can keep warm for four hours, 90 ⁰С can keep warm for two hours.
DRY OPERATION SAFETY
The kettle is equipped with a system the automatically turns it off when it is
accidentally turned on without water or with an insufficient amount of water inside.
If the system is tripped disconnect the kettle from power supply and let it cool down
for 15 minutes.
After that you may resume operation of the appliance.
An unpleasant odor may occur if the safety is tripped.
DIGITAL KETTLE OPERATION
- Position the kettle base on a dry and flat surface and away from any potential
heat source
- Unwind the length of cord required to reach the mains electrical outlet. Ensure
the cord does not hang over the work surface edge
- Remove the kettle from the base
- Open the lid. Fill the kettle with cool water, between the MIN and MAX markings
located inside the kettle.
- Close the lid and place the kettle back onto its base. Make sure that the lid is
securely closed before boiling.
NOTE:
Always remove the kettle from its base before filling. Do not fill the kettle
above the MAX mark or below the MIN mark on the water gauge.
- Plug the kettle into the mains electrical outlet.
- Press the power switch and its indicator will light up, and then the kettle starts
to boil the water. Once you have made your touch-control selection, the kettle
will sound with notification tone, indicating that the selected function is about
to start.
- The display shows the real-time temperature, the 40, 60 and 90 ⁰С
setting lights will be on, the default selection is 100 ⁰С, and the 100 ⁰С light
flashes, then enter into temperature selection stage.
- Press the «+» and «-» keys to select the temperature. During the temperature
selection process, the selected temperature light keep flashing and the other light
stay on.
KEEP WARM
After temperature selecting, press «ПОДОГРЕВ» (KEEP WARM) button, the
display will only show the selected temperature and the selected light on only.
The kettle start to working, After the water boiled to the selected temperature,
there will be a short-beep and automatically enter the keep warm stage. After
4-hours keep warm, the buzzer will beep triple, all the lights will off to end
the keep warm stage, the kettle go into standby stage.
START/CANCEL
After temperature selecting, press «ПУСК/ОТМЕНА» (START/CANCEL) button, the
display will only show the selected temperature and the selected light on only. The
kettle start to work, After the water boiled to the selected temperature, the buzzer
will beep triple, all the lights will off, the kettle go into standby stage.
NOTE
- When the kettle enter into temperature selection stage, If there is no operation within
1 minute, the buzzer will sounds triple, All lights are off, and the product enters the
standby state.
- The display should always display the real-time temperature after power on;
- The default selection is 100 ⁰С after power on;
- After entering the working state, you can only exit the program by pressing the
«ПУСК/ОТМЕНА» (START/CANCEL) key.
- There will be ±5 ⁰С tolerance different from the setting temperature.
- During operation, the digital display will illuminate with real time temperature and
count up as the water temperature increases. The digital display will also countdown
in real time as the water temperature decreases.
- Ensure that switch is free of obstructions and the lid is firmly closed,
the kettle will not turn off if the switch if be constrained or if the lid is opening
- The kettle will switch off automatically and the indicator will turn off once the
water has boiled. If necessary, it will take you 30 seconds to wait before pressing the
power switch again to re-boil the water. You may shut off the
power by directly lifting the kettle from the power base at any moment or press the
«ПУСК/ОТМЕНА» (START/CANCEL) key to stop boiling process.
- Lift the kettle from the power base and then pour the water.
16