Текст страницы
(10, 11, 12) will be switched on, and the temperature of
the water in the kettle will be shown on the display (6).
– To fill the kettle with water, remove it from the base (8),
which the backlight of the buttons (10, 11, 12) and the
display (6) will go out.
– You can switch the operating kettle off by pressing the
the backlight of the touch buttons (10, 11, 12) and the
display (6) will go out, then open the lid (3) by pressing
the lid opening button (4).
– Fill the kettle with water not over the maximum mark
power button
(11), the kettle flask backlight will be
switched off, after which the backlight of the touch but
tons (10, 11, 12) and display (6) will go out.
– After switching the kettle off wait for 10-20 seconds,
«MAX», but not under the minimum mark «MIN».
– Close the lid (3) and put the full kettle on the base (8).
after which you can switch it on to heat the water once
more.
Note: You can choose temperature measurement unit:
°С or °F by pressing and holding the button (10) for more
than 3 seconds.
Make sure that the kettle lid (3) is closed tightly. You
will hear a sound signal and will see the backlight of the
touch buttons (10, 11, 12), and the temperature of the
water in the kettle will be shown on the display (6).
Note: If no button is pressed, then the display (6) and the
backlight of the touch buttons (10, 11, 12) will go out. To
switch the kettle on again, press the button
(11) again.
Boiling mode
– To boil water, press the button
(11). The boiling
process will begin, the temperature of the water will be
shown on the display (6), and you will also see the back
light of the buttons (10, 11, 12) and the flask of the kettle.
– After the water boils, you will hear three sound signals,
the boiling process will stop, the kettle flask backlight will
be switched off, after some time the display (6) and the
touch button backlight (10, 11, 12) will go out.
– You can switch the operating kettle off by pressing the
power button
(11), the kettle flask backlight will be
switched off, after which the display (6) and the back
light of the touch buttons (10, 11, 12) will go out.
– After switching the kettle off, wait for 10-20 seconds,
after which you can switch it on to boil water again.
Water heating mode
– This kettle also allows you to heat water to a tempera
Keep Warm mode
To set the temperature for the Keep Warm mode, press the
button
(11), you will hear a sound signal, the backlight
of the touch buttons (10, 11, 12) and the display (6) will be
switched on. Press and hold the button (12) for more than
3 seconds, the Keep Warm mode indicator (13) will appear
on the display (6) and the temperature indications will be
flashing. By pressing the button (10) select the desired
heating temperature in the range from 40 to 90 °C with an
increment of 10 °C, it will be shown on the display (6), after
that press the button
(11) again. The kettle will maintain
the set temperature for 2 hours provided that the kettle has
not been removed from the base (8). In this case, the dis
play (6) will show the maintained water temperature, Keep
Warm mode indicator (13), and you will also see the back
light of the buttons (10, 11, 12) and the kettle flask.
Note: If the temperature of the Keep Warm mode is higher
than the temperature of the water in the kettle, the kettle
will heat the water to the set temperature, after which it will
switch to the Keep Warm mode.
To switch the Keep Warm mode off press the button
(11), the kettle flask backlight will be switched off, after
which the display (6) and the backlight of the touch buttons
(10, 11, 12) will go out.
Note: If you accidentally switch the kettle on without water,
the automatic thermal fuse will trip and the kettle will be
switched off. In this case take the kettle from the base (8),
let it cool down for 10-15 minutes, then fill it with water and
switch it on, the kettle will operate in normal mode.
Note: There is a cord storage (9) on the reverse side of the
base (8). Adjust the optimal power cord length by folding it
in a corresponding way.
ture in the range from 40 to 90 °C with an increment
of 10 °C. To select the desired heating temperature,
press the button
(11), you will hear a sound sig
nal, and the backlight of the touch buttons (10, 11, 12)
will be switched on. By pressing the button (10) select
the desired heating temperature which will be shown
on the display (6), then press the button
(11) once
more. The heating process will start, the temperature of
the water will be shown on the display (6), and you will
also see the backlight of the buttons (10, 11, 12) and the
flask of the kettle.
– When the water is heated to the set temperature, you will
CLEANING AND CARE
– Before cleaning disconnect the unit from the mains, pour
hear three sound signals, the heating process will stop,
the backlight of the kettle flask will be switched off, after
out water and let the kettle cool down.
11