Текст страницы
PL
PL
EN
EN
Always place the kettle on a stable, smooth, flat surface; the power cord must not hang loosely off the edge of a
table (or any other work surface) or touch a heated surface.
Do not use the kettle with the lid open.
Do not remove the lid when the water is boiling.
If the internal electrical elements are flooded with water, make sure the kettle is completely dry before plugging in.
Do not move while the kettle is switched on.
Unplug the product immediately from the mains in the event of any breakdown or damage and contact an official
technical support service. In order to prevent any risk of danger, do not open the device. Only qualified technical
personnel from the brand´s Official technical support service may carry out repairs or procedures on the device.
B&B TRENDS SL. disclaims all liability for damages that may occur to people, animals or objects, for the non-
observance of these warnings.
INSTRUCTIONS FOR USE
Before use
Make sure that all the product’s packaging has been removed.
Before heating water for the first time, we recommend using the kettle twice, in order to clean the system.
Boiling water
1.
Open the lid. Fill the kettle through the lid opening with a minimum of 500ml (2 cups) of water.
2.
DO NOT attempt to fill the kettle it is plugged into the wall outlet.
DO NOT use for other than boiling water. Other liquids will contaminate the interior of the kettle.
DO NOT fill past the MAX level printed on the glass. Overfilling may cause water to spit out when boiling.
3.
Close the lid.
4.
Place kettle and base on a flat, level, dry, heat resistant surface. Ensure that it is correctly engaged on the base.
5.
Plug in to a wall outlet. The display will show the actual water temperature. The kettle is now in standby mode.
NOTE: if no selection has been made in 30 sec., the display will shut off and the kettle will enter sleep mode.
Press any button once to “wake up: the kettle.
6.
Direct kettle spout away from cabinets, walls etc. to prevent possible steam damage.
This appliance is intended to be used in household. It is not
intended to be use in applications such as: -staff kitchen areas
in shops, offices and other working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
Never immerse the appliance in water or any other liquid.
If the kettle is overfilled, boiling water may be ejected.
Appliance is only to be used with the stand provided.
Warning: avoid spillage on the connector
Warning: potential injury from misuse!
Heating element surface is subject to residual heat after use.
Allow the kettle to cool completely before cleaning.
Always remove the plug from the mains before cleaning the
kettle.
Do not use any abrasive cleaning agents – such as emulsions,
creams, pastes, etc. – for cleaning the kettle.
This appliance is intended for use at a maximum altitude of
2000m above sea level.
7.
The default temperature is 100°C (212°F). The variable temperature range is 40 to 100°C (105-212°F) in 10
degree C increments.
8.
To boil water :
•
Press the power button
once.
•
To switch between the C and F display press the °C/°F button for 3 sec.
IMPORTANT WARNINGS
Any incorrect use or improper handling of the product shall render the warranty null and void.
•
The display will show 100°C (212°F) for 3 sec. then the display will switch to the actual water
temperature. The display temperature will increase until the kettle reaches 100°C (212°F).
•
Once the water has boiled the kettle will shut off.
Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product
label.
•
The display will show 100°C (212°F) for 30 sec. then the display will shut off.
The mains connection cable must not be tangled or wrapped around the product during use.
9.
To use the variable temperature settings:
Do not use the device, or connect and disconnect to the supply mains with the hands and / or feet wet.
Do not pull on the connection cord in order to unplug it or use it as a handle.
•
Press the °C/°F button until you reach the desired temperature between 40-100°C (105-212°F) in 10
degree C increments.
•
To switch between the C and F display, press the °C/°F button and hold for 3 sec.
Only fill the kettle with water. Milk and instant beverages will burn and damage the appliance. Never operate the
kettle without water and do not over fill it; observe the min and max markings. If the kettle is too full, the water
will boil over!
•
Display will show the chosen temperature for 3 sec. then will switch to the actual water temperature.
The display temperature will increase until it reaches the chosen temperature.
Do not put the jug on a stove or in a microwave for re-heating of water.
•
Once the temperature has reached the set temperature the kettle will shut off
11
10