Текст страницы
6
7
en
en
• Unwind the power cord to its full length when using
the unit.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
USING THE HOT AIR STYLER
DELIVERY SET
1.
Hot air styler – 1 pc
2.
Thermal brushes – 3 pcs
3.
Instruction manual – 1 pc
• If the hot air styler turns off during operation, set
the switch (1) to the position «0», unplug the unit
and make sure that the air inlets and outlets are
unblocked.
• Let the unit cool down for 5-10 minutes and switch it
on again. Do not block the air inlets during the unit
operation and do not let hair be caught into the air
inlets (8).
TECHNICAL SPECIFICATIONS
CLEANING AND MAINTENANCE
- Supply voltage: 220-240 V, ~ 50/60 Hz
- Rated input power: 950 W
• For good results, wash your hair with shampoo, wipe
it with a dry towel, dry with a hairdryer and comb it,
then start styling your hair.
• Unwind the power cord completely.
• Install one of the thermal brushes (4, 5, 6) into the
installation place and turn the lock (3) clockwise as
far as it will go. Make sure that the installed thermal
brush is fixed properly.
• Set the operation mode switch (1) into the 0 position.
• Insert the power plug into the mains socket.
• Using the switch (1), select the required operation
mode:
ATTENTION!
Do not allow children to play with
polyethylene bags or packaging film.
Danger of suffocation!
• The hot air styler is intended for household use only.
• Set the switch (1) to the position «0» and unplug the
unit, wait until the installed thermal brush cools down.
• Remove the installed thermal brush by turning the
lock (3) counterclockwise.
• Wipe the unit body (7) with a slightly damp cloth, and
then wipe it dry.
• Clean the air inlets (8) with a brush.
• Do not immerse the unit into water or any other
liquids.
• Do not use abrasives and solvents to clean the unit’s
body (7) and the thermal brushes (4, 5, 6).
STORAGE
• Wind a hair lock around the installed thermal brush,
select the brush rotation direction with the buttons (2)
< ˃; when the hair lock is wound around the brush,
release button (2) and the thermal brush will stop
rotating.
• Depending on your hair type, select the necessary
operation mode with the switch (1).
• To fix the lock, set the operation mode switch (1) to
the position «C», «cool air» supply.
• Switch the hot air styler off by setting the operation
mode switch (1) to the position «0».
• Take the hair lock off the thermal brush.
• Notes:
--
if you have trouble taking the thermal brush from
the hair, turn the unit off by setting the switch (1) to
the position «0», disconnect the installed thermal
brush and carefully remove it from the hair lock.
--
during operation, avoid contact of the hot surface
of the thermal brush (4, 5, 6) with your face, neck
and other parts of your body.
• After you finish using the unit, set the switch (1) to
the position «0» and unplug the unit.
• Wait until the thermal brush cools down.
• Remove the thermal brush (4, 5, 6) by turning the
lock (3) counterclockwise as far as it will go.
Overheating protection
• The overheating protection switches the unit off if the
outgoing air is too hot.
--
«0» – the hairdryer is off
--
«C» – «cool air» supply
--
«1» – low temperature
--
«2» – high temperature
• Buttons < ˃ (2) activate clockwise/counterclockwise
rotation of the thermal brush (4, 5, 6). During the
operation, press and hold down button (2), the brush
(4, 5, 6) will rotate in the required direction.
• Note: - during the first use, the heating element
may produce a foreign smell and a small amount of
smoke, this is normal and it is not a warranty event.
• Divide the hair into locks.
• Use the operation mode switch (1) to set the required
operation mode.
• Disconnect the unit from the mains and clean it.
• Never wind the power cord around the hot air styler,
as this can damage the cord or the unit’s body.
• For convenient storage, the hot air styler has a
hanging loop (9) that you can hang it on, provided
that in this position the unit is not exposed to water.