Текст страницы
For tool with firm fit detent pin
ASSEMBLY
Optional accessory
► Fig.13: 1. Impact socket 2. Hole 3. Square drive
4. Detent pin
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct impact socket
To install the socket, align the hole in the side of the socket with
the detent pin on the square drive, and then, push it onto the
square drive until it locks into place. Tap it lightly if required.
To remove the socket, depress the detent pin through the
hole in the socket and pull the socket off the square drive.
NOTE: The firm fit detent pin may fit too securely to
remove the socket.
Always use the correct size impact socket for bolts and
nuts. An incorrect size impact socket will result in inac-
curate and inconsistent fastening torque and/or damage
to the bolt or nut.
In that case, depress the firm fit detent pin fully and
pull the socket off the square drive.
Installing or removing impact socket
Installing hook
Optional accessory
CAUTION: Make sure that the impact socket
and the mounting portion are not damaged before
installing the impact socket.
CAUTION: When installing the hook, always
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
► Fig.14: 1. Groove 2. Hook 3. Screw
CAUTION: After inserting the impact socket,
make sure that it is firmly secured. If it comes out,
do not use it.
NOTE: The way of impact socket installation varies
depending on the type of the square drive on the tool.
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
Tool with the ring spring
Ring
Country specific
Model TW007G
For impact socket without O-ring and pin
► Fig.10: 1. Impact socket 2. Square drive 3. Ring
spring
CAUTION: Before using the ring, always
make sure that the bracket and ring are secured
and not damaged.
Push the impact socket onto the square drive until it
locks into place.
CAUTION: Use the hanging/mounting parts
for their intended purposes only. Using for unin-
tended purpose may cause accident or personal
injury.
To remove the impact socket, simply pull it off.
For impact socket with O-ring and pin
► Fig.11: 1. Impact socket 2. O-ring 3. Pin
► Fig.15: 1. Bracket 2. Ring 3. Screws
The ring is convenient for hanging the tool with hoist.
First, place the rope through the ring. Then hang the
tool up to the air with hoist.
OPERATION
Move the O-ring out of the groove in the impact socket
and remove the pin from the impact socket. Fit the
impact socket onto the square drive so that the hole in
the impact socket is aligned with the hole in the square
drive.
Insert the pin through the hole in the impact socket and
square drive. Then return the O-ring to the original posi-
tion in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
Tool with the detent pin
CAUTION: Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator, it is not locked completely. Insert it fully
until the red indicator cannot be seen. If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
► Fig.16
Model TW008G
For tool with light fit detent pin
► Fig.12: 1. Impact socket 2. Hole 3. Square drive
4. Detent pin
To install the socket, align the hole in the side of the
socket with the detent pin on the square drive, and then,
push it onto the square drive until it locks into place. Tap
it lightly if required.
To remove the socket, simply pull it off.
Hold the tool firmly and place the impact socket over the bolt or
nut. Turn the tool on and fasten for the proper fastening time.
The proper fastening torque may differ depending upon
the kind or size of the bolt, the material of the workpiece
to be fastened, etc. The relation between fastening
torque and fastening time is shown in the figures.
11
ENGLISH