Текст страницы
when it is not performing properly. Try a different accessory
or speed setting to achieve the desired result.
MAINTENANCE AND CLEANING
along with the correct Dremel accessory and attachment,
to do the work for you. Do not put pressure on the
tool during use, if possible. Instead, lower the spinning
accessory lightly to the work surface and allow it to touch
the point at which you want to begin. Concentrate on
guiding the tool over the work using very little pressure
from your hand. Allow the accessory to do the work.
Usually it is better to make a series of passes with the tool
rather than to do the entire job with one pass. A gentle touch
gives the best control and reduces the chance of error.
!
NO USER SERVICEABLE PARTS INSIDE.
PREVENTIVE MAINTENANCE PERFORMED BY
UNAUTHORIZED PERSONNEL MAY RESULT IN
INCORRECT CONNECTION OF INTERNAL WIRING AND
COMPONENTS WHICH COULD CAUSE SERIOUS
HAZARD.
The tool can be cleaned most effectively with compressed
dry air. Always wear safety goggles when cleaning
tools with compressed air.
!
TO AVOID ACCIDENTS, ALWAYS DISCONNECT THE
TOOL AND/OR CHARGER FROM THE POWER
SUPPLY BEFORE CLEANING
HOLDING THE TOOL
Always hold the tool away from your face. Accessories
can be damaged during handling and can fly apart as
they come up to speed.
When holding tool, do not cover the ventilation
openings with your hand. Blocking the ventilation
openings could cause the motor to overheat.
For best control in close work, grip the multitool like a
pencil between your thumb and forefinger. A
q
The “golf” grip method is used for heavier operations such
as grinding or cutting. A
a
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool
by inserting pointed objects through an opening.
!
CERTAIN CLEANING AGENTS AND SOLVENTS
DAMAGE PLASTIC PARTS. Some of these are:
gasoline, carbon tetrachloride, chlorinated cleaning solvents,
ammonia and household detergents that contain ammonia.
ON/OFF
The tool is switched “ON” by the slide switch located on
the top side of the motor housing.
TO TURN THE TOOL “ON”, slide the switch button up, to
position 1, 2, 3 or 4.
TO TURN THE TOOL “OFF”, slide the switch button down,
to position “0”.
SERVICE AND WARRANTY
FIVE POSITION SLIDE SWITCH A
s
Your tool is equipped with a five position switch.
The speed may be adjusted during operation by sliding the
switch up or down between any of the settings.
To select the right speed for each job, use a practice
piece of material.
We recommend that all tool service be performed by a
Dremel Service Centre.
This Dremel product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling are
excluded from the warranty.
In case of a complaint, send the undismantled tool and/or
charger and proof of purchase to your dealer.
OPERATING SPEEDS A
s
Refer to the chart on pages 8-9 to help determine the
proper speed for the material being worked on and the
accessory to use.
Do not exceed 15,000 rpm when using wire brushes.
CONTACT DREMEL
For more information on service and warranty, the Dremel
product range, support and hotline, go to www.dremel.com.
NOISE AND VIBRATION
Sound pressure level (standard deviation 3dB) dB(A)
<70
Vibration (triax vector sum) m/s2
<2.5
Vibration uncertainty K m/s2
1.5
Most jobs can be accomplished using the tool at the highest
setting. However, certain materials (some plastics and
metals) can be damaged by high-speed generated heat and
should be worked on at relatively low speeds. Low speed
operation (15,000 rpm or less) is usually best for polishing
operations employing the felt polishing accessories. All
brushing applications require lower speeds to avoid wire
discharge from the holder. Let the performance of the tool
do the work for you when using lower speed settings. Higher
speeds are better for hardwoods, metals and glass and for
drilling, carving, cutting, routing and shaping.
NOTE: The declared vibration total value(s) and the
declared noise emission value(s) have been measured in
accordance with a standard test method and may be used
for comparing one tool with another. They may also be
used in a preliminary assessment of exposure.
The vibration and noise emissions during actual use of
the power tool can differ from the declared total value
depending on the ways in which you use the tool. Make an
estimation of the exposure in the actual conditions of use
and identify the safety measures for personal protection
accordingly (taking account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle in addition to the trigger time).
Some guidelines regarding tool speed:
•
Plastic and other materials that melt at low
temperatures should be cut at low speeds.
•
Polishing, buffing and cleaning with a wire brush must
be done at speeds no greater than 15,000 rpm to
prevent damage to the brush and your material.
•
Wood should be cut at high speed.
•
Iron or steel should be cut at high speed.
•
If a high speed steel cutter starts to vibrate, it usually
indicates that it is running too slowly.
•
Aluminium, copper alloys, lead alloys, zinc alloys and
tin may be cut at various speeds, depending on the
type of cutting being done. Use a paraffin (not water)
or other suitable lubricant on the cutter to prevent the
cut material from adhering to the cutter teeth.
NOTE: Increasing pressure on the tool is not the answer
14