Текст страницы
GETTING STARTED: BEFORE YOUR FIRST BREW
FILL THE BEAN HOPPER
WATER FILTER INSTALLATION
ENGLISH
• Great tasting coffee starts with great water.
Water filters help to remove chlorine, odors
and other impurities that may be in your
water to give you great tasting coffee.
4 Place test strip on a dry, flat surface and wait 1
minute for test strip to display results.
REMOVE ACCESSORIES & PARTS FROM
PACKAGING
1 Remove the lid of the hopper, fill hopper with
beans, then place the lid securely back on the
hopper. Ensure the handle in the hopper is
in the locked position when installed on the
hopper.
• To start, remove all accessories and parts from
packaging. Ensure that all accessories and
parts are removed from the packaging before
discarding packaging.
5 After 1 minute, you will see 0–5 purple squares
appear. This will indicate the water hardness
level of the water (0 purple squares=level 0,
5 purple squares=level 5, etc.)
Very
Soft
Very
Hard
• When removing the machine from packaging,
be sure to remove all tape from machine. Tape
will be on all sides of the machine.
1 Soak Water Filter
for 5 minutes.
2 Rinse water filter and
mesh for 60 seconds.
hd 0
hd 1
hd 2
hd 3
hd 4
hd 5
CLEAN ACCESSORIES BEFORE USE
• After removing all accessories and parts from
the packaging, thoroughly clean all parts by
hand-washing and dry thoroughly.
Green
Squares
Purple
Squares
2 Fill hopper with whole beans. DO NOT add
pre-ground beans to bean hopper.
WATER HARDNESS TEST
4 Set date 2 months
ahead.
6 After identifying the water hardness level, plug in
the machine.
3 Remove end-cap
from filter housing
and insert filter. Clip
end-cap back onto
filter housing to
secure filter in place.
7 Look at the left side of the control panel. It will
display hd 5.
All water has minerals that can cause buildup in the
machine over time. These minerals are referred to
as water hardness, and will impact how often you
will need to descale the machine. Doing this test
will ensure the machine recommends a descale at
the right time.
1 Remove test strip from pack.
8 Rotate the centre dial to program the water
hardness level by matching the number of
purple squares on the test strip to the number
displayed. (e.g., if the result is level 1, change the
setting to hd 1).
5 Install filter housing
into reservoir.
3 Ensure the handle in the hopper is in the
locked position when installed on the hopper,
then place lid securely back on the hopper.
FILL THE WATER RESERVOIR
2 Completely submerge the water test strip in the
water you plan on using with the machine for
5–10 seconds.
• Before you begin, make sure the water
reservoir is full of room-temperature or cold
water. Be sure to fill up to but not exceeding
the maximum fill line.
9 Press centre dial to confirm your setting.
3 Pull test strip out and lightly shake it.
NOTE: If you need to change the hardness level,
purchase another test strip at ninjakitchen.eu/
ninja-parts-accessories/. For more instructions
on how to reset the water hardness, refer the
Additional Settings section.
If at any point before a brew there's not enough
water in the reservoir to brew your selected
drink, the machine will indicate that you must
ADD WATER. If you get an ADD WATER
notification while brewing, add water to the
reservoir and press START BREW to resume.
NOTE: DO NOT put any water in the grinder.
If water does get in the grinder, please call us
at +44 (0)800 862 0453 immediately.
NOTE: DO NOT fill the reservoir with hot
water, use room-temperature or cold water.
If you use hot water, you may get a ADD
WATER notification.
73
72
ninjakitchen.eu
ninjakitchen.eu