Текст страницы
WIRELESS ACTIVATION FUNCTION
NOTICE: Always use the hooks on the back of
the lid when removing the wireless unit. If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
What you can do with the wireless
activation function
Tool registration for the vacuum
cleaner
NOTE: A Makita vacuum cleaner supporting the
wireless activation function is required for the tool
registration.
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
► Fig.36
NOTE: Finish installing the wireless unit to the tool
before starting the tool registration.
NOTE: During the tool registration, do not pull the
switch trigger or turn on the power switch on the
vacuum cleaner.
To use the wireless activation function, prepare follow-
ing items:
•
A wireless unit (optional accessory)
•
A vacuum cleaner which supports the wireless
activation function
NOTE: Refer to the instruction manual of the vacuum
cleaner, too.
The overview of the wireless activation function
setting is as follows. Refer to each section for detail
procedures.
If you wish to activate the vacuum cleaner along with
the switch operation of the tool, finish the tool registra-
tion beforehand.
1.
Installing the wireless unit
2.
Tool registration for the vacuum cleaner
1.
Install the batteries to the vacuum cleaner and the
tool.
3.
Starting the wireless activation function
Installing the wireless unit
2.
Set the stand-by switch on the vacuum cleaner to
"AUTO".
► Fig.40: 1. Stand-by switch
Optional accessory
CAUTION: Place the tool on a flat and stable
surface when installing the wireless unit.
3.
Press the wireless activation button on the vac-
uum cleaner for 3 seconds until the wireless activation
lamp blinks in green. And then press the wireless acti-
vation button on the tool in the same way.
► Fig.41: 1. Wireless activation button 2. Wireless
activation lamp
NOTICE: Clean the dust and dirt on the tool
before installing the wireless unit. Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
If the vacuum cleaner and the tool are linked success-
fully, the wireless activation lamps will light up in green
for 2 seconds and start blinking in blue.
NOTICE: To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTE: The wireless activation lamps finish blinking
in green after 20 seconds elapsed. Press the wireless
activation button on the tool while the wireless acti-
vation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in green, push the wire-
less activation button briefly and hold it down again.
NOTICE: When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
NOTE: When performing two or more tool registra-
tions for one vacuum cleaner, finish the tool registra-
tion one by one.
1.
Open the lid on the tool as shown in the figure.
► Fig.37: 1. Lid
2.
Insert the wireless unit to the slot and then close
the lid.
Starting the wireless activation
function
NOTE: Finish the tool registration for the vacuum
cleaner prior to the wireless activation.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.38: 1. Wireless unit 2. Projection 3. Lid
4. Recessed portion
NOTE: Refer to the instruction manual of the vacuum
cleaner, too.
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
► Fig.39: 1. Wireless unit 2. Hook 3. Lid
After registering a tool to the vacuum cleaner, the
vacuum cleaner will automatically runs along with the
switch operation of the tool.
1.
Install the wireless unit to the tool.
After removing the wireless unit, keep it in the supplied
case or a static-free container.
ENGLISH
2.
Connect the hose of the vacuum cleaner with the
tool.
► Fig.42
22