Текст страницы
Installing side grip (handle)
Installing or removing depressed
center wheel or flap disc
Optional accessory
CAUTION: Always be sure that the side grip is
installed securely before operation.
Screw the side grip securely on the position of the tool
as shown in the figure.
► Fig.3
WARNING: When using a depressed center
wheel or flap disc, the wheel guard must be fitted
on the tool so that the closed side of the guard
always points toward the operator.
CAUTION: Make sure that the mounting part
of the inner flange fits into the inner diameter of
the depressed center wheel / flap disc perfectly.
Mounting the inner flange on the wrong side may
result in the dangerous vibration.
Installing or removing wheel guard
(For depressed center wheel, flap
disc, flex wheel, wire wheel brush
/ abrasive cut-off wheel, diamond
wheel)
WARNING: When using a depressed center
wheel, flap disc, flex wheel or wire wheel brush,
the wheel guard must be fitted on the tool so that
the closed side of the guard always points toward
the operator.
Mount the inner flange onto the spindle.
Make sure to fit the dented part of the inner flange onto
the straight part at the bottom of the spindle.
Fit the depressed center wheel / flap disc on the inner
flange and screw the lock nut onto the spindle.
► Fig.7: 1. Lock nut 2. Depressed center wheel
3. Inner flange 4. Mounting part
WARNING: When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
► Fig.8: 1. Lock nut wrench 2. Shaft lock
(In some European countries, when using a diamond
wheel, the ordinary guard can be used. Follow the
regulations in your country.)
To remove the wheel, follow the installation procedure
in reverse.
Super flange
For tool with locking screw type
wheel guard
Optional accessory
Only for tools with M14 spindle thread.
Models with the letter F are standard-equipped with
Super flange. Only 1/3 of efforts needed to undo lock
nut, compared with conventional type.
Installing or removing flex wheel
Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the bear-
ing box. Then rotate the wheel guard to such an angle
that it can protect the operator according to work. Be
sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
► Fig.4: 1. Wheel guard 2. Bearing box 3. Screw
Optional accessory
For tool with clamp lever type wheel
guard
WARNING: Always use supplied guard when
flex wheel is on tool. Wheel can shatter during use
and guard helps to reduce chances of personal injury.
► Fig.9: 1. Lock nut 2. Flex wheel 3. Back up pad
4. Inner flange
Follow instructions for depressed center wheel but also
use back up pad over wheel. See order of assembly on
accessories page in this manual.
Loosen the screw, and then pull the lever in the direc-
tion of the arrow. Mount the wheel guard with the protru-
sions on the wheel guard band aligned with the notches
on the bearing box. Then rotate the wheel guard to such
an angle that it can protect the operator according to
work.
► Fig.5: 1. Wheel guard 2. Bearing box 3. Screw
4. Lever
Installing or removing abrasive disc
Optional accessory
► Fig.10: 1. Sanding lock nut 2. Abrasive disc
3. Rubber pad
Pull the lever in direction of the arrow. Then tighten the
wheel guard with fastening the screw. Be sure to tighten
the screw securely. The setting angle of the wheel
guard can be adjusted with the lever.
► Fig.6: 1. Screw 2. Lever
1.
Mount the rubber pad onto the spindle.
To remove wheel guard, follow the installation proce-
dure in reverse.
2.
Fit the disc on the rubber pad and screw the sand-
ing lock nut onto the spindle.
3.
Hold the spindle with the shaft lock, and securely
tighten the sanding lock nut clockwise with the lock nut
wrench.
9
ENGLISH