Текст страницы
cable.
• DISCHARGE residual pressure before disconnecting the
high pressure cleaner hose.
• If you are too far from the object you wish to clean, do
not move the cleaner nearer by pulling on the high pres
sure hose; use the handle provided.
• Before using the high pressure cleaner, CHECK every
time that the screws are fully tightened and that there are
no broken or worn parts.
• Do not obstruct the ventilation grilles during operation.
• Only USE detergents which will not corrode the coating
materials of the high pressure hose/electrical cable
• The cross-section of any extension cables used must be
proportional to their length, i. e. the longer the extension
cable, the greater the cross-section; cables with a protec
tion level of “IPX5” must be used.
• ENSURE that all people or animals keep a minimum dis
tance of 16 yd. (15m) away.
• Position the high pressure cleaner AS NEAR POSSIBLE to
the water supply.
ASSEMBLY
• Connecting water hose to inlet first,and turn on the tap.
Make sure the machine is full of water. . Then turn on the
main switch. The most important thing is not forget to
press the in electronic control center to start the machine.
• Use the high pressure cleaner only with accessories and
replacement parts authorized by the manufacturer. The
use of original accessories and replacement parts will en
sure safe, trouble-free operation.
• Avoid unintentional firing of the trigger. Do not carry
the lance / trigger assembly with your hand over the trig
ger. Always use the trigger lock mechanism.
• The electronic control center has three pressure modes
for users to choose. There are soft, medium and strong
mode. The pressure depends upon which attachment is
best suited to the surface you are cleaning.
• If you want to increase the pressure level, press the +
button in the electronic control center.
• Ensure that the safety lock on the trigger is used, when
you have stopped using the pressure washer to prevent
accidental operation.
• If you want to reduce the pressure level, press the - but
ton in the electronic control center.
• Do not use the cleaner with inflammable or toxic liquids,
or any products which are not compatible with the correct
operation of the high pressure cleaner.
• Do not direct the water jet towards the unit itself, electri
cal parts or towards other electrical equipment.
• When you increase the pressure level to make the
pressure indicator turn red, it means that the machine is
working at the maximum pressure. At this time, please do
not let the machine work continuously for more than 15
minutes under the maximum pressure.
• Do not allow children or incompetent persons to use
the high pressure cleaner.
• Do not touch the plug and/or socket with wet hands.
PRE-OPERATION
Adjusting fan pattern
• Do not use the high pressure cleaner if the electrical ca
ble is damaged.
• Do not use the high pressure cleaner if the high pressure
hose is damaged.
Water can be sprayed either with a narrow jet or fan-
shaped. The kit includes 4 nozzles with a non-adjustable
spray angle of 0o, 15o, 25o, 40o. Install the required nozzle
before starting work, depending on the task.
• Do not jam the trigger in the operating position.
Nozzle cleaning instructions
• Check that the data plates are affixed to the high pres
sure cleaner, if not, inform your dealer. Cleaners without
plates must NOT be used as they are unidentifiable and
potentially dangerous.
A clogged or partially clogged nozzle can cause a signif
icant reduction of water coming out of the nozzle and
cause the unit to pulsate while spraying. To clean out the
nozzle:
• Do not tamper with or alter the calibration of the safety
valve.
• Do not alter the original diameter of the spray head
nozzle.
1. Turn off and unplug unit.
• Do not leave the high pressure cleaner unattended.
2. Turn off water supply. Relieve any pressure trapped in
the hose by squeezing trigger 2-3 times.
• Do not move the high pressure cleaner by pulling on the
electrical cable.
3. Separate lance from gun.
• All electrical conductors MUST BE PROTECTED against
the water jet.
4. Rotate nozzle to the narrow stream setting. This opens
up the fan blades.
• The high pressure cleaner MUST ONLY BE CONNECTED
to a correctly earthed power supply.
5. Using included tip cleaner, or an unfolded paper clip,
insert wire into the nozzle hole and move back and forth
until debris is dislodged.
• The high pressure may cause materials to bounce off
surfaces at speed; therefore protective clothing and safety
goggles MUST BE WORN.
6. Remove additional debris by back-flushing water
through the nozzle. To do this, place end of a garden hose
(with water running) to end of nozzle for 30-60 seconds.
• Before doing work on the cleaner, REMOVE the plug.
• Before pressing the trigger, GRIP the gun firmly to coun
teract the recoil.
EXPLOITATION
• Maintenance and/or repair of electrical components
MUST be carried out by qualified staff.
When spraying water against a surface, maximum impact
is generated when the water strikes the surface “head on.”
10