Текст страницы
OBJ_BUCH-1742-004.book Page 12 Friday, August 19, 2016 2:47 PM
12 | English
8 Service indicator
9 Stand-by indicator
10 Auxiliary handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
min-1
Rotary Hammer
GBH 5-40 DCE
Article number
3 611 B64 0..
Rated power input
W
1150
Speed
min-1
170 – 340
Impact rate
– Drilling mode
– Chiselling mode
mm
40
mm
mm
min-1
1500 –2900
1500 –3050
Impact energy per stroke
according to EPTA-Procedure
05/2009
J
8.8
Chisel positions
12
Tool holder
SDS-max
Lubrication
Central permanent
lubrication
Max. drilling dia.
– Concrete (with twist drill)
– Concrete
(with break-through drill bit)
– Brickwork (with core bit)
parts of the power tool “live” and could give the operator an
electric shock.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
55
90
Weight according to
EPTA-Procedure 01:2014
kg
6.8
Protection class
/II
Product Description and Specifica-
tions
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for hammer drilling in concrete,
brick and stone as well as for chiselling.
Sound emission values determined according to
EN 60745-2-6.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K
determined according to EN 60745-2-6:
Hammer drilling into concrete: ah= 10.5 m/s2, K= 4.4 m/s2
Chiselling: ah= 7.5 m/s2, K= 1.5 m/s2
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
3 Mode selector switch
4 Vibration damper
5 On/Off switch
6 Handle (insulated gripping surface)
7 Thumbwheel for speed preselection/impact frequency
preselection
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
1 609 92A 2GB | (23.5.18)
Bosch Power Tools