Текст страницы
Rotation only
Switch action
For drilling in wood, metal or plastic materials, rotate
the action mode changing knob to the
symbol. Use a
twist drill bit or wood drill bit.
► Fig.7: 1. Action mode changing knob
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
► Fig.3: 1. Switch trigger
ASSEMBLY
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Lighting up the front lamp
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
► Fig.4: 1. Switch trigger 2. Lamp
Side grip (auxiliary handle)
CAUTION: Do not look in the light or see the
source of light directly.
CAUTION: Always use the side grip to ensure
safe operation.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
CAUTION: After installing or adjusting the
side grip, make sure that the side grip is firmly
secured.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Install the side grip so that the grooves on the grip fit in
the protrusions on the tool barrel. Turn the grip clock-
wise to secure it. The grip can be fixed at desired angle.
► Fig.8: 1. Side grip
Reversing switch action
► Fig.5: 1. Reversing switch lever
Grease
CAUTION: Always check the direction of
rotation before operation.
Coat the shank end of the drill bit beforehand with a
small amount of grease (about 0.5 - 1 g).
This chuck lubrication assures smooth action and lon-
ger service life.
Installing or removing drill bit
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION: When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
Clean the shank end of the drill bit and apply grease
before installing the drill bit.
► Fig.9: 1. Shank end 2. Grease
Insert the drill bit into the tool. Turn the drill bit and push
it in until it engages.
After installing the drill bit, always make sure that the
drill bit is securely held in place by trying to pull it out.
► Fig.10: 1. Drill bit
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Selecting the action mode
To remove the drill bit, pull the chuck cover down all the
way and pull the drill bit out.
► Fig.11: 1. Drill bit 2. Chuck cover
Depth gauge
NOTICE: Do not rotate the action mode chang-
ing knob when the tool is running. The tool will be
damaged.
NOTICE: To avoid rapid wear on the mode
change mechanism, be sure that the action mode
changing knob is always positively located in one
of the action mode positions.
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the side grip and insert the depth
gauge into the hole on the side grip. Adjust the depth
gauge to the desired depth and tighten the side grip
firmly.
► Fig.12: 1. Hole 2. Depth gauge
Rotation with hammering
NOTE: Make sure that the depth gauge does not
touch the main body of the tool when attaching it.
For drilling in concrete, masonry, etc., rotate the action
mode changing knob to the
symbol. Use a car-
bide-tipped drill bit.
► Fig.6: 1. Action mode changing knob
9
ENGLISH