Текст страницы
Electronic function
Insert the drill bit into the tool. Turn the drill bit and push
it in until it engages.
After installing the drill bit, always make sure that the
drill bit is securely held in place by trying to pull it out.
► Fig.21: 1. Drill bit
To remove the drill bit, pull the chuck cover down all the
way and pull the drill bit out.
► Fig.22: 1. Drill bit 2. Chuck cover
Chisel angle (when chipping,
scaling or demolishing)
The tool is equipped with the electronic functions for
easy operation.
•
Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
•
Active Feedback sensing Technology (For
HR001G/HR002G)
If the tool is swung at the predetermined accelera-
tion during operation, the motor is forcibly stopped
to reduce the burden on the wrist.
NOTE: This function does not work if the acceleration
does not reach the predetermined one when the tool
is swung.
The chisel can be secured at the desired angle. To
change the chisel angle, rotate the action mode chang-
ing knob to the O symbol. Turn the chisel to the desired
angle.
► Fig.23: 1. Action mode changing knob
NOTE: If the bit is swung at the predetermined
acceleration during chipping, scaling, or demolishing,
the motor is forcibly stopped. In this case, release
the switch trigger, and then pull the switch trigger to
restart the tool.
Rotate the action mode changing knob to the
sym-
bol. Then make sure that the chisel is securely held in
place by turning it slightly.
Depth gauge
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
The depth gauge is convenient for drilling holes of
uniform depth.
Press and hold the lock button, and then insert the
depth gauge into the hex hole. Make sure that the
toothed side of the depth gauge faces the marking.
► Fig.24: 1. Depth gauge 2. Lock button 3. Marking
4. Toothed side
Side grip (auxiliary handle)
Adjust the depth gauge by moving it back and forth
while pressing the lock button. After the adjustment,
release the lock button to lock the depth gauge.
CAUTION: Always use the side grip to ensure
safe operation.
NOTE: Make sure that the depth gauge does not
touch the main body of the tool when attaching it.
CAUTION: After installing or adjusting the
side grip, make sure that the side grip is firmly
secured.
Installing or removing the dust
collection system
To install the side grip, follow the steps below.
Optional accessory
1.
Loosen the thumb screw on the side grip.
► Fig.18: 1. Thumb screw
To install the dust collection system, insert the tool into
the dust collection system all the way until it locks in
place with a little double click.
► Fig.25
2.
Attach the side grip while pressing the thumb
screw so that the grooves on the grip fit in the protru-
sions on the tool barrel.
► Fig.19: 1. Thumb screw
3.
Tighten the thumb screw to secure the grip. The
grip can be fixed at desired angle.
To remove the dust collection system, pull the tool while
pressing the lock-off button.
► Fig.26: 1. Lock-off button
Grease
Dust cup
Optional accessory
Coat the shank end of the drill bit beforehand with a
small amount of grease (about 0.5 - 1 g).
This chuck lubrication assures smooth action and lon-
ger service life.
Installing or removing drill bit
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Model
Bit diameter
Dust cup 5
6 mm - 14.5 mm
Clean the shank end of the drill bit and apply grease
before installing the drill bit.
► Fig.20: 1. Shank end 2. Grease
Dust cup 9
12 mm - 16 mm
► Fig.27: 1. Dust cup
18
ENGLISH