Текст страницы
ENGLISH
Explanation of general view
21. Front grip
22. Clamping screw
23. Rip fence (Guide rule)
24. Adjusting screw for 45° (BSS610
only)
25. Adjusting screw for 90°
26. Triangular rule
27. Limit mark
28. Brush holder cap
29. Screwdriver
- Hex wrench
- Inner flange
- Saw blade
- Outer flange
- Hex. bolt
- Dust nozzle (accessory)
- Screw
- Hose
- Vacuum cleaner
- Rear handle
1.
Red part
2.
Button
3.
Battery cartridge
4.
Lever
5.
Stopper
6.
Base
7.
Cutting line
8.
Switch trigger
9.
Lock-off lever
10. Shaft lock
SPECIFICATIONS
Model
BSS610
BSS611
Blade diameter
165 mm
at 90°
57 mm
Max. Cutting depth
at 45°
40 mm
at 50°
36 mm
No load speed (min-1)
3,700
Overall length
347 mm
Net weight
3.5 kg
3.3 kg
Rated voltage
D.C. 18V
•
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
•
Specifications and battery cartridge may differ from country to country.
•
Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
ENE028-1
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
CORDLESS CIRCULAR SAW
SAFETY WARNINGS
GEB060-1
tool may contact hidden wiring. Contact with a “live”
wire will also make exposed metal parts of the power
tool “live” and shock the operator.
6. When ripping always use a rip fence or straight
edge guide. This improves the accuracy cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
9. Causes and Operator Prevention of Kickback:
- kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the
operator;
- when the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator;
- if the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade to
climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below.
Danger:
1. Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw,
they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece. Do not attempt to remove cut material
when blade is moving.
CAUTION: Blades coast after turn off. Wait until blade
stops before grasping cut material.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support and
workpiece support. (Fig. 1)
5. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
5