Текст страницы
Important safety notes!
Know Your Projector
Remote control
Projection Distance
Installation methods
Projection size
Depending on your use environment and requirements, the projector
can be hung forward with a special hanger on the ceiling or placed on
a smooth desktop and projected forward onto the screen. Of course,
you can also use other ways to install the projector according to the
following legend.
Installation
To achieve the best effect, please use the projector in a darker
room or draw the curtains.Be careful when use the projector. Any
dropping or bump may lead to damaged parts, blurred images or
display improperly.
air input IR/ Focus camera Lens
air output Power ON/OFF Line network port
HDMI USB Audio output
Power input Indicator light Hanger fixing hole
Tripod hole Lift foot
V1.0
Referring to the data in the following table, place the projector at the
required distance from the projection screen according to the preset
image size.
During installation, place the projector on a solid, smooth countertop
or install on the ceiling.The area around the fuselage should be well
ventilated. Do not cover or block the vents. Within 30cm distance of
the vents, there should be no any shielding objects.
Bracket lifting positive projection
Bracket lifting back projection
Power Source
Be careful to use power cord to avoid excessive bending.
Damaged power cord may cause electric shock and fire.Please
be careful when using this machine. Falling or striking may
damage components, blur images or display abnormally.
Projection size(inch)
Projection distance(meter)
1.75
60
80
2.28
100
2.81
Tabletop placement
positive projection
Tabletop placement back projection
Note: The projection sizes and distance is for your reference.
Note:
Power
Setting
Menu
Foucs-
Cleaning
Unplug the power cord.Clean the cabinet regularly with a damp
cloth. Neutral detergent can be used. Do not use strong
detergents or solvents (such as alcohol and thinner). The lens
should be cleaned with glasses cloth or lens paper. Be careful not
to scratch the lens.Please regularly use a soft brush to clean the
air inlet filter , vent and loudspeaker of the machine, otherwise
the vent will be blocked by dust accumulation, causing
overheating of the machine, which will lead to machine failure.
In order that the projected image will not show geometric distortion
(trapezoidal shape), install the projector vertically on the symmetry
axis of the screen. See below.
Up
Foucs+
Left
OK
Wright
Down
Return
Home
In the projection setting interface, select "Projection" to switch
Vol-
Vol+
Mute
Source
High Temperature Attention
Do not disassemble the projector casually since there may be a
risk of electric shock, which affects normal maintenance.Liquid or
heavy objects should not allowed to put on the machine.
The screen has a right
symmetry axis
1.When using the lifting method, the projector should not rise above
the upper edge of the screen, otherwise, it will affect the effect of the
image or the trapezoidal correction.
2.Be sure to install the projector on the symmetrical axis line on the
left and right sides of the screen to avoid causing trapezoidal
distortion on the left and right sides of the image.
The projector is biased to
the right, the projection
image will large on the left
and small on the right
Suitable for areas below 2000m altitude.
The projector is biased
to the left, the projection
image small on the left
and large on the right
The installation position
and angle are correct,
and the projection
image is correct.
35
Note：
1.The remote control must be on the front and rear of
the projector, if facing the image,
the remote control sensitivity will decrease.
2.The remote control will be different as different
model .
0
Please use in an ambient temperature of 0-35 degrees Celsius
.
Note
The figure is a schematic diagram, with different specification and slightly different graphics;
The input interface will be different according to the different model, the model you have shall
prevail.
1
2
3
4
5
How to mirroring with your iPhone
Keystone
Simply Troubleshooting
1.The projector and your iPhone connect with same WiFi.
2. Projector: Enter to the APPS to find “AirScreen”or“TV Casting”.
3.iPhone: Find mirroring function on your iPhone and connect with
the projector.
When the projector raises / lowers or side projection, the image will
deform and distortion. You can select "SETTING" and PROJECTOR,
then enter the correction in "4-point Trapezoid" or "4-side
Trapezoid".
How to Play U-disk
3.After the installation of the projector should be well ventilated,
there can be no object to cover or block the vent of the projector.
4.Please do not connect the power during the installation, to avoid
electric shock risk or projector circuit failure.
5.The image may appear trapezoid distortion and blur at the first
boot time. Please refer to the "Correction of Images" section for
adjustment.
Connect the USB with projector, press key on the remote,
Enter the USB page, select Picture, Audio, Video, Store.
Power on
Note: When the tilt Angle of the machine is too
large,the definition of the image will decrease.
How to work with Bluetooth Speaker
How to use Bluetooth
Connect the power cord to the projector and press the OK button
for 3 seconds; or press the remote control at the front / rear
infrared window and press the " " power button to start the device.
Shutdown: Long press the power button for 3 seconds; or point the
remote control at the front / rear infrared window of the body, press
" " to select the shutdown after shutdown.
Interface operation instructions
1.Projector: Enter the Apps and find “Blue Tooth Speker”
2.Phone: Turn on the bluetooth on you phone, connect “Projector
BT”with projector
Enter the SETTING page, select “BLUETOOTH”; Search and
select the Bluetooth that you need to pair with.
How to go to the Source selection
Image correction
Focus regulation
Go to the home page, press the signal source button" "on the
remote control, select the required signal source channel, such
as "HDMI" , “USB ", and press the OK key of the remote control to
enter the corresponding signal source state.
The projector is easlly working as TV, generally will not
encounter any problems, but may be due to the near by
equipment or voltage reasons, some false fault, please remove
the fault before repair, if the customer still can not eliminate the
fault, please contact the relevant staff.
1.The power supply indicator light is not on.
Whether the power supply plug is well inserted properly.
2.Press the power button on the remote control cannot turn on.
Whether the remote control battery is out of power.
Whether by the strong light to illuminate the projector receiver.
3.The projection with out picture.
Whether the signal source selection of the projector is correct.
Whether the signal source is well inserted.
4.After the projection for a period of time, it automatically turns
off.
Whether the voltage is too low, or whether the voltage fluctuates
too much。
5.Unable to read U-disk.
Only support FAT 32, NTFS U disk format,if not the first two
format, can change the format through formatting.
6.The picture is blurred.
Please keep the picture at least 50inch or 1.5 meters away until
the picture is clear.
The range of autofocus is 1.5-3 meters, beyond this range,
please manually focus.
How to Miracast with your Android Phone
Dust cleaning
The image will automatically focus after power on or moving the
projector . If the automatic focus does not reach the clearest state
of the image, please press the remote control "F +" and "F-" keys to
fine-tune until the image is adjusted to the clearest effect.You can
enter SETTING to close Autofocus function , select PROGECTOR,
select Auto Focus off.
1.Projector page: select “Miracast”
2.Android phone: Enter the Setting page to select mirroring
function, connect with the projector.
How to connect WiFi
Enter the main interface, SETTING, ENTWORK-WiFi;find the
network you want to connect to and press Confirm. Enter the
password via the virtual keyboard and confirm the connection.
1.Clean the dust filter once every three
months and replace the dust filter once
every six months.
2.Cleaning steps: shut off the projector,
disconnect the power cord, remove the
dust net from the bottom of the fuselage,
blow the dust with the air duct, remove the
dust and then install it into the projector. If
the dust cannot be removed, a new dust
filter must be replaced.
6
7
8
9
10