Текст страницы
10
11
EN
EN
RECYCLING
Cleaning the outlet filter (17)
Cleaning the HEPA filter (19) and the separator (20)
installed in the dust bin (11)
differ from the given value, depending on the room
temperature.
• If the vacuum cleaner does not switch on, it may be
caused by another malfunction. In this case apply to
a service center.
STORAGE
To prevent possible damage to the
environment or harm to the health of
people by uncontrolled waste disposal,
after expiration of the service life of the
unit or the batteries (if included), do not
discard them with usual household waste,
but take the unit and the batteries to specialized stations
for further recycling.
• Switch the vacuum cleaner off and unplug the power
cord plug from the mains socket.
• Remove the outlet filter grid (18), turning it clockwise
and remove the outlet filter (17) (pic. 9).
• Wash the outlet filter (17) and the grid (18) under a
lukewarm water jet. Do not wash the outlet filter (17)
and the grid (18) in a dishwashing machine.
• Dry the outlet filter (17) and the grid (18).
• Install the outlet filter (17) back to its place.
• Install the grid (18) back to its place, turn the grid (18)
counterclockwise as far as it will go.
The waste generated during the recycling of the unit
is subject to mandatory collection and consequent
recycling in the prescribed manner.
Vacuum cleaner body
• Before taking the vacuum cleaner away for long
storage, clean the unit body, the dust bin (11), the
HEPA filter (19), the separator (20), the dust bin flask
(23) and the outlet filter (17).
• For easy storing of the vacuum cleaner, use the
brush storage (15) (pic. 4).
• Keep the vacuum cleaner in a dry cool place out of
reach of children and disabled persons.
DELIVERY SET
For further information about recycling of this product,
apply to the local municipal administration, a household
waste recycling service or to the shop where you
purchased this product.
The manufacturer reserves the right to change the
appearance, design and specifications not affecting
the general operation principles of the unit, without
prior notice.
• Clean the vacuum cleaner body with a soft, slightly
damp cloth, and then wipe it dry. Provide that no
liquid gets inside the vacuum cleaner body.
• Do not use solvents or abrasives for cleaning the
vacuum cleaner body and the attachments.
• Do not immerse the vacuum cleaner body, the power
cord and the power plug into water or any other
liquids.
The unit operating life is 3 years
OVERHEATING PROTECTION
1.
Vacuum cleaner with the dust bin and filters
installed – 1 pc.
2.
Flexible hose – 1 pc.
3.
Telescopic extension pipe – 1 pc.
4.
Floor/carpet brush – 1 pc.
5.
Combined crevice nozzle – 1 pc.
6.
Furniture/furniture upholstery brush - 1 pc.
7.
Instruction manual – 1 pc.
• Preliminarily remove dust and garbage from the dust
bin (11) as described above.
• Pull the lock (21) of the upper lid (22) and open the
lid (22) (pic. 7)
• Remove the separator (20) (pic. 7), turn the HEPA
filter (19) clockwise and remove it (pic. 8).
• Remove dust and garbage from the separator (20)
(pic. 8).
• Wash the separator (19) under a warm water jet and
then dry it.
• Wash the HEPA filter (19) under a warm water jet and
dry it (pic. 8).
• Do not wash the parts in a dishwashing machine.
• Dry the HEPA filter (19) thoroughly.
• Do not dry the HEPA filter (19) with a hairdryer or
similar appliances.
• Wash the dust bin flask (23), wipe it and dry.
• Install the HEPA filter (19) in the separator (20) and
turn it counterclockwise as far as it will go.
• Insert the separator (20) into the flask (23).
• Close the lid (22) until the lock (21) catches.
• Install the assembled dust bin (11) back to its place,
make sure that the dust bin (11) is fixed properly.
The manufacturing date is specified in the serial
number.
SPECIFICATIONS
Attention!
In case of any malfunctions, promptly apply to the
authorized service center.
• If the electric motor gets too hot during the operation,
the overheating protection system will be set off.
• If during cleaning the vacuum cleaner has switched
off, press the on/off button (16) and unplug the unit.
• Let the vacuum cleaner cool down for 30-40 minutes
and switch it on again. The cool-down time can
- Power supply: 220-240 V ~ 50 Hz
- Rated input power: 1800 W
- Suction power: 400 W
Before assembling and installing the dust bin (11)
back to its place, make sure that the HEPA filter (19),
the separator (20) and the flask (23) are dry.