Текст страницы
A10-17—Water Level Float
A10-18—Cleaning Tank Filter
A10-19—Cleaning Tank
Attach the base by pressing down
both sides of the base firmly, and
then pressing the connecting part in
the middle until you hear a click.
A11 Power Cord Storage
B2-2—Click
When moving the dock, secure the water tanks to
prevent it from falling off.
Note:
A11-1—Cord Outlets
A11-2—Power Port
A11-3—Cord Storage Slot
B2-3—Connect the power cord to the back
of the dock, and keep the excess cord
inside the storage slot.
Power cord can exit at either side.
Note:
Installation
B
• The dock status indicator light turns red if an error occurs.
• Place the dock on a flat floor away from fire, heat, and
water. Avoid narrow spaces or locations where the robot
may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may
cause the dock to tilt over and cause problems docking
and departing.
• Keep the dock away from direct sunlight or anything
that may block the dock location beacon; otherwise,
the robot may fail to return to the dock.
• Do not use the dock without clean water tank, dirty
water tank, dust container cover, disposable dust bag,
or cleaning tank.
• Maintain the dock according to the maintenance instructions.
Do not clean the dock with a wet cloth or tissue.
• All docks are subject to water-based tests before
leaving the factory. It is normal that a small amount of
water remains in the waterway of the dock.
B1 Important Information
B2-4—Align and install the mop axles into
the robot in place until you hear a click.
B4 Powering On & Charging
B2-5—Click
B3 Place the Dock
B1-1—Tidy cords, hard or sharp objects
(such as nails and glass), and loose
items from the ground and move
any unstable, fragile, precious, or
dangerous items to prevent personal
injury or property damage due to
items becoming tangled in, struck by,
or knocked over by the robot.
Press and hold the
button to power on the
robot. Wait until the power light is steady, and
then place the robot on the dock to charge.
Make sure the dock is powered on. Press
the button on the robot to make the robot
automatically return to the dock for charging.
The robot is equipped with a built-in high-
performance lithium-ion rechargeable battery
pack. To maintain battery performance, keep
the robot charged.
Keep a space of clearance about 0.9 m (2.9
ft) in height, 0.4 m (1.3 ft) in length and 1.2
m (3.9 ft) in width. Place the dock on a hard
and flat floor (wood/tile/concrete etc.), flat
against a wall. Make sure the location has
good WiFi for a better experience with the
mobile app, and then plug it in and make
sure the dock status indicator light is on.
B1-2—When using the robot in a raised
area, always use a secure physical
barrier to prevent accidental falls
that may result in personal injury or
property damage.
Note:
B4-1—Dock Status Indicator Light turns
off, Robot Power Indicator Light
breathing: Charging
B3-1—About 0.9 m (2.9 ft)
B3-2—About 0.4 m (1.3 ft)
B3-3—About 1.2 m (3.9 ft)
Notes:
When using the robot for the first time, follow
it throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
The robot may not be turned on when the battery
is low. In this case, place the robot to the dock for charging.
Note:
B2 Assembly
B2-1—Place the dock on a hard and flat floor.
• If the power cord hangs vertically to the ground, it
may be caught by the robot, causing the dock to be
moved or disconnected.
• The dock status indicator light is on when the dock is
powered on, and off when the robot is charging.
36