Текст страницы
ENGLISH
– Remove stems of herbs, shell nuts.
– Remove bones, sinews and cartilage from meat.
USING THE WHISK
Use the whisk attachment (11) only for beating cream and egg
whites, making biscuit dough or for mixing ready desserts.
WARNING: Before installing the whisk (11) and the gear
(12) make sure that the power plug is not inserted into the
mains socket.
Chopping
Caution: the blades of the chopping knife (8) are very sharp!
Always hold the chopping knife (8) by the upper plastic end.
••
Place the chopper bowl (7) on a flat stable surface.
••
Set the chopping knife (8) on the axis inside the chop
per bowl (7).
••
Put the products into the chopper bowl (7).
Note: Do not switch the unit on when the chopper bowl (7)
is empty.
••
Insert the whisk attachment (11) into the whisk gear (12).
••
Insert the whisk gear (12) into the motor unit (3) and turn it
counterclockwise until bumping, make sure that the gear
(12) and the whisk (11) are fixed properly.
••
Insert the power plug into the mains socket. Put the whisk
attachment (11) into the bowl with products.
••
Put the whisk attachment (11) into the bowl with products.
Note: You can put the foodstuffs into the measuring cup (10).
••
Place the geared lid (9) on the chopper bowl (7) and rotate
it clockwise until bumping.
••
Install the motor unit (3) on the geared lid (9) feeding
chute, turn it counterclockwise until bumping, make sure
that the motor unit (3) is fixed properly.
••
Install the motor unit (3) strictly in the vertical position
and evenly.
– To connect the unit to the mains, insert the power plug into
the mains socket.
– To switch the unit on, press and hold down the button (5).
••
To switch the unit on, press and hold down the button (5).
Turn the attachment rotation speed control knob (6) to
change the whisk (11) rotation speed.
••
If you press and hold down the «TURBO» button (4), the
unit will operate at maximum rotation speed.
••
After you finish using the unit, take the power plug out of
the mains socket, disconnect the whisk gear (12) from the
motor unit (3) by turning it clockwise.
••
Remove the whisk (11) from the gear (12).
ATTENTION!
– Do not use the whisk attachment (11) to knead tight
Turn the attachment rotation speed control knob (6) to
change the chopping knife (8) rotation speed.
– If you press and hold down the «TURBO» button (4), the
dough.
– Put products into the bowl before switching the unit on.
chopping knife (8) will rotate at maximum rotation speed.
– During the unit operation hold the motor unit (3) with one
hand and the chopper bowl (7) with the other hand.
– After using the unit, wait until the chopping knife (8) fully stops.
– Unplug the unit.
– Disconnect the motor unit (3) from the geared lid (9) feed
USING THE CHOPPER
The chopper is used to chop meat, cheese, onion, herbs, gar
lic, carrots, walnuts, almonds, prunes, vegetables and fruit.
ATTENTION!
Do not chop very hard products, such as ice cubes, frozen
products, nutmegs, coffee beans, cereals etc.
ing chute by turning it clockwise.
– Remove the geared lid (9).
– Carefully remove the chopping knife (8) taking it by the
Before you start chopping:
– Cut meat, cheese, onions, vegetables or fruit into pieces
approximately 2x2 cm in size.
plastic end.
– Take the chopped food out of the chopper bowl (7).
ATTENTION!
Strictly follow the described sequence of operations.
To achieve the best results, refer to the table below:
Function
Product type
Maximum weight
Approximate processing
time, seconds
Speed
Chopping (chopper)
meat
150 g
10
TURBO
Carrot + water
240 g (carrot)
60
TURBO
Chopping and mixing
(Blender)
360 g (water)
Beating (Whisk)
Egg whites
90
TURBO
Note: all data in this table are given as recommendations.
6