Текст страницы
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE: If you remove the recipro saw blade without
rotating the blade clamp lever fully, the lever may not
be locked in the released position
. In this case,
rotate the blade clamp lever fully again, then make
sure that the blade clamp lever locked at the released
position
.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE: When the tool is overheated, the lamp blinks
for one minute. In this case, cool down the tool before
another operation.
NOTE: If the blade clamp lever is positioned inside
the tool, switch on the tool just a second to let the
blade out. Remove the battery cartridge from the tool
before installing or removing the recipro saw blade.
ASSEMBLY
OPERATION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION: Always press the shoe firmly
against the workpiece during operation. If the
shoe is removed or held away from the workpiece
during operation, strong vibration and/or twisting will
be produced, causing the blade to snap dangerously.
Installing or removing the recipro
saw blade
CAUTION: Always wear gloves to protect
your hands from hot flying chips when cutting
metal.
CAUTION: Be sure to always wear suitable
eye protection which conforms with current
national standards.
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and around the
blade clamp. Failure to do so may cause insufficient
tightening of the blade, resulting in a serious injury.
CAUTION: Always use a suitable coolant
(cutting oil) when cutting metal. Failure to do so will
cause premature blade wear.
CAUTION: Do not quirk the blade during
cutting.
To install the recipro saw blade, always make sure that
the blade clamp lever (part of the blade clamp sleeve)
is in released position
on the insulation cover before
inserting the recipro saw blade. If the blade clamp lever
is in fixed position, rotate the blade clamp lever in the
direction of the arrow so that it can be locked at the
released positon
.
► Fig.5: 1. Blade clamp lever 2. Released position
3. Fixed position
Press the shoe firmly against the workpiece. Do not
allow the tool to bounce. Bring the recipro saw blade
into light contact with the workpiece. First, make a pilot
groove using a slower speed. Then use a faster speed
to continue cutting.
► Fig.8
Insert the recipro saw blade into the blade clamp as far
as it will go. The blade clamp sleeve rotates and fixes
the recipro saw blade. Make sure that the recipro saw
blade cannot be extracted even though you try to pull
it out.
► Fig.6: 1. Recipro saw blade 2. Blade clamp sleeve
MAINTENANCE
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation. This can
be extremely dangerous.
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To remove the recipro saw blade, rotate the blade
clamp lever in the direction of the arrow fully. The reci-
pro saw blade is removed and the blade clamp lever is
fixed at the released position
.
► Fig.7: 1. Recipro saw blade 2. Blade clamp lever
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
CAUTION: Keep hands and fingers away from
the lever during the switching operation. Failure
to do so may cause personal injuries.
7
ENGLISH