Текст страницы
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Adjusting the shoe
TШăТЧstКХХătСОărОМТЩrШ/УТРăsКаăЛХКНО,ăХШШsОЧătСОăЛШХtăЛвă
СОбăаrОЧМС.ăАСОЧăТЧstКХХТЧРăКărОМТЩrШăsКаăЛХКНО,ăЩrОssă
tСОăЛШХtăаТtСătСОăСОбăаrОЧМСătШăШЩОЧătСОăsХШtăНurТЧРă
ТЧsОrtТЧРătСОăЛХКНО.
►Fig.10: ń.ăRОМТЩrШ/УТРăsКаăЛХКНОă ă
2.ăBХКНОăМХКЦЩă
3.ăHШХОăПШrărОМТЩrШăsКаăЛХКНОă ă
4.ăHШХОăПШrăУТРăsКаă
ЛХКНО
►Fig.5: ń.ăHОбăаrОЧМСă ă
2.ăHОбăЛШХtă
3.ăLШШsОЧ
►Fig.11
АСОЧătСОăЛХКНОăХШsОsăТtsăМuttТЧРăОПiМТОЧМвăТЧăШЧОăЩХКМОă
along its cutting edge, reposition the shoe to utilize a
sСКrЩ,ăuЧusОНăЩШrtТШЧăШПăТtsăМuttТЧРăОНРО.ăTСТsăаТХХăСОХЩă
tШăХОЧРtСОЧătСОăХТПОăШПătСОăЛХКНО.
TШărОЩШsТtТШЧătСОăsСШО,ăХШШsОЧătСОăЛШХtăаТtСăСОбăаrОЧМС.ă
Slide the shoe to the desired position and then tighten
tСОăЛШХtăirЦХв.
ВШuăМКЧăusОăЛШtСăУТРăsКаăЛХКНОsă(BătвЩО)ăКЧНărОМТЩrШă
sКаăЛХКНОsăКММШrНТЧРătШăвШurăаШrФ.ăIЧsОrtătСОărОМТЩrШ/
УТРăsКаăЛХКНОăstrКТРСtăТЧtШătСОăЛХКНОăМХКЦЩăКЧНătТРСtОЧă
ТtăЛвăСОбăаrОЧМС.ăPuХХătСОărОМТЩrШ/УТРăsКаăЛХКНОăХТРСtХвătШă
ЦКФОăsurОătСКtătСОărОМТЩrШ/УТРăsКаăЛХКНОăНШОsăЧШtăПКХХăШППă
during operation.
TШărОЦШЯОătСОărОМТЩrШ/УТРăsКаăЛХКНО,ăПШХХШаătСОăТЧstКХХК-
tion procedure in reverse.
Hex wrench storage
ASSEMBLY
►Fig.12: 1. Hex wrench
2. Protrusion
When not in use, store the hex wrench as shown in the
iРurОătШăФООЩăТtăПrШЦăЛОТЧРăХШst.
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro/jig
saw blade
OPERATION
CAUTION: Always clean out all chips or foreign
matter adhering to the blade, blade clamp and/or
slider.ăFКТХurОătШăНШăsШăЦКвăМКusОăТЧsuПiМТОЧtătТРСtОЧ-
ТЧРăШПătСОăЛХКНО,ărОsuХtТЧРăТЧăКăsОrТШusăТЧУurв.
CAUTION: ůХаКвsăprОssătСОăsСШОăirЦХвă
against the workpiece during operation. If the
shoe is held away from the workpiece during opera-
tТШЧ,ăstrШЧРăЯТЛrКtТШЧăКЧН/ШrătаТstТЧРăаТХХăЛОăЩrШНuМОН,ă
МКusТЧРătСОăЛХКНОătШăsЧКЩăНКЧРОrШusХв.
For Model JR103D
►Fig.6: ń.ăRОМТЩrШăsКаăЛХКНОă
2.ăBХКНОăМХКЦЩăsХООЯО
CAUTION: Always wear gloves to protect your
СКЧНsăПrШЦăСШtălвТЧРăМСТpsăаСОЧăМuttТЧРăЦОtКХ.
CAUTION: Be sure to always wear suitable eye
protection which conforms with current national
standards.
IЧsОrtătСОărОМТЩrШăsКаăЛХКНОăТЧtШătСОăЛХКНОăМХКЦЩăКsăПКră
КsăТtăаТХХăРШ.ăTСОăЛХКНОăМХКЦЩăsХООЯОărШtКtОsăКЧНăiбОsă
tСОărОМТЩrШăsКаăЛХКНО.ăMКФОăsurОătСКtătСОărОМТЩrШăsКаă
ЛХКНОăМКЧЧШtăЛОăОбtrКМtОНăОЯОЧătСШuРСăвШuătrвătШăЩuХХă
it out.
CAUTION: ůХаКвsăusОăКăsuТtКЛХОăМШШХКЧtăĚМut-
tТЧРăШТХěăаСОЧăМuttТЧРăЦОtКХ. Failure to do so will
МКusОăЩrОЦКturОăЛХКНОăаОКr.
►Fig.13
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.ăTСТsăМКЧă
ЛОăОбtrОЦОХвăНКЧРОrШus.
NOTE:ăВШuăМКЧăЧШtăusОătСОăУТРăsКаăЛХКНОăаТtСă
JRńŃ3D.
►Fig.7: ń.ăRОМТЩrШăsКаăЛХКНОă
2.ăBХКНОăМХКЦЩăsХООЯО
PrОssătСОăsСШОăirЦХвăКРКТЧstătСОăаШrФЩТОМО.ăDШăЧШtă
КХХШаătСОătШШХătШăЛШuЧМО.ăBrТЧРătСОărОМТЩrШăsКаăЛХКНОă
into light contact with the workpiece. First, make a pilot
РrШШЯОăusТЧРăКăsХШаОrăsЩООН.ăTСОЧăusОăКăПКstОrăsЩООНă
to continue cutting.
►Fig.14
►Fig.15
TШărОЦШЯОătСОărОМТЩrШăsКаăЛХКНО,ărШtКtОătСОăЛХКНОă
МХКЦЩăsХООЯОăТЧătСОăНТrОМtТШЧăШПătСОăКrrШаăПuХХв.ăTСОărОМТ-
ЩrШăsКаăЛХКНОăТsărОЦШЯОНăКЧНătСОăЛХКНОăМХКЦЩăsХООЯОăТsă
iбОНăКtătСОărОХОКsОНăЩШsТtТШЧ.
You can use the switch lever or trigger according to your
work.
NOTE: If the tool is operated continuously until the
ЛКttОrвăМКrtrТНРОăСКsăНТsМСКrРОН,ăКХХШаătСОătШШХătШărОstă
ПШrăń5ăЦТЧutОsăЛОПШrОăЩrШМООНТЧРăаТtСăКăПrОsСăЛКttОrв.
NOTE:ăIПăвШuărОЦШЯОătСОărОМТЩrШăsКаăЛХКНОăаТtСШută
rШtКtТЧРătСОăЛХКНОăМХКЦЩăsХООЯОăПuХХв,ătСОăsХООЯОă
ЦКвăЧШtăЛОăiбОН.ăIЧătСТsăМКsО,ărШtКtОătСОăЛХКНОă
МХКЦЩăsХООЯОăПuХХв,ătСОЧăЦКФОătСОăsХООЯОăiбОНăКtătСОă
released position.
For Model JR105D
►Fig.8: 1. Hex wrench
2. Bolt
3. Loosen
4.ăTТРСtОЧ
►Fig.9: ń.ăRОМТЩrШăsКаăЛХКНОă
2.ăHОбăаrОЧМСă ă
3.ăHШХОăПШrărОМТЩrШăsКаăЛХКНОă ă
4.ăBХКНОăМХКЦЩ
7
ENGLISH