Текст страницы
Indicator lamp
Installing or removing the blade cover
CAUTION: Be careful not to touch the blades
when installing or removing the blade cover.
The indicator lamp blinks or lights up when the remain-
ing battery capacity is low or empty. The indicator lamp
also lights up when the tool becomes overloaded.
► Fig.4: 1. Indicator lamp
Lamp status and action to be taken
To remove the blade cover, pull it slightly, and then slide
it sideways. To install the blade cover, perform the steps
in reverse.
► Fig.7
Indicator lamp
Status
Action to be taken
The lamp blinks
red.
The remaining bat-
tery capacity is low.
Charge the battery.
Installing or removing the grass receiver
Charge the battery.
Optional accessory
The lamp lights up
red. *
The tool has stopped
because the remain-
ing battery capacity
is empty.
Turn off the tool.
CAUTION: When installing or removing the
grass receiver, be sure to attach the blade cover
and be careful not to trap your fingers between
the tool and grass receiver.
The tool has
stopped due to
overload.
Installing the grass receiver
* The time at which the indicator lamp lights up varies depending
on the temperature around the work area and the battery car-
tridge conditions.
1.
Hook the hinge of the grass receiver on the groove
of the tool.
► Fig.8: 1. Hinge 2. Grass receiver
Adjusting the shearing height (for
grass shear)
Optional accessory
2.
Align the protrusions on the grass receiver with
the grooves on the tool by sliding the grass receiver
toward the front of the tool and moving it in the direction
of the arrow.
► Fig.9
CAUTION: When changing the shearing
height, be sure to attach the blade cover and be
careful not to trap fingers between the tool and
grass receiver.
NOTICE: Do not attach the hinge of the grass
receiver to the tool forcibly after aligning the pro-
trusions on the grass receiver with the grooves
on the tool.
The shearing height can be set to three levels (15 mm,
20 mm, and 25 mm) by changing the fixed position of
the grass receiver. The shearing height without the
grass receiver is about 10 mm.
Removing the grass receiver
1.
Slide the grass receiver toward the front of the tool.
► Fig.5: 1. Grass receiver
1.
Release the protrusions on the grass receiver
from the grooves on the tool while sliding the grass
receiver toward the front of the tool.
► Fig.10: 1. Grass receiver
2.
Change the fixed position of the grass receiver by
moving it in the direction of the arrow.
► Fig.6
2.
Release the hinge of the grass receiver from the
tool.
NOTE: The shearing height value is a guideline. The
actual shearing height may vary depending on the
condition of the lawn or the ground.
Installing or removing the shear
blades for grass shear
NOTE: Try a test shearing in a less conspicuous
place to get your desired height.
NOTICE: If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
ASSEMBLY
Removing the shear blades
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
1.
Remove the grass receiver if it's installed. Place
the tool upside down.
► Fig.11
CAUTION: When replacing the shear blades,
always wear gloves and attach the blade cover so
that your hands and face do not directly contact
the blades.
2.
While pressing the lock lever, turn the undercover
counterclockwise until
on the undercover is aligned
with
on the lock lever.
► Fig.12: 1. Undercover 2. Lock lever
NOTICE: When replacing the shear blades, do
not wipe off grease from the gear and crank.
3.
Remove the undercover, shear blades, and crank.
► Fig.13: 1. Undercover 2. Shear blades 3. Crank
16
ENGLISH