Текст страницы
NOSE AND EAR TRIMMER
5. CARE OF THE APPLIANCE
ATTENTION!
4. OPERATION
CHARGER
- Attach the nose and ear trimmer attachment to the main
- Before using the appliance for the first time, it is necessary
- Make sure the instrument is turned off and the (USB) cord is
unplugged from the power source.
- Wipe the body of the instrument with a damp cloth. At the
body of the appliance.
- Press the power button.
- Place the tip of the trimmer into the nasal cavity. Make
to charge the battery for 16 hours to ensure normal
operation of the machine.
- To do this, make sure the device is switched off. Connect the
cable plug to the socket on the instrument and the USB plug
to the power supply.
- The charge indicator will light up. When the battery is fully
same time, make sure that moisture does not get inside
the case.
- Do not use abrasives or solvents to clean the case.
- The device must not be cleaned by immersion in water.
charged, the indicator will turn off.
CLEANING THE CLIPPING HEAD
circular motions while inserting and removing the nozzle.
Use the nose, ear and brow clipper to trim the brow line. You
shouldn’t cut her eyebrows.
NOTE: Make sure the nasal cavity is clean before using the
nozzle. Please do not insert the tip of the trimmer into the
nose and ear canal deeper than 0.5 cm.
ATTENTION!
- Press on the top of the paddle and detach the blade from the
MICROTRIMMER
- Do not use the appliance in a bathtub or shower room.
- Do not expose the device to direct sunlight or other sources
- Attach the micro trimmer attachment to the main body of
head of the attachment.
- Clean the nozzle of hair with a brush.
- Place the blade back into the head of the attachment and
put some oil on the blade.
of heat.
- Use the appliance with dry hands only.
- Do not use the instrument if the power cord is frayed or
the appliance.
- Press the power button.
- You can start modeling a beard or edging a haircut.
CLEANING THE RAZOR HEAD
LCD DISPLAY
loose in the power socket on the instrument.
- Before use, lubricate the clipper blade with the special oil
- Remove the shaving head from the shaving head by
that comes with the kit.
188
USE OF NOZZLES
HAIR CUTTER
pressing the buttons on both sides of the shaving head base.
- Shake the shaving head to shake the hair out of it.
- Clean the rest of the hair with a brush.
- Put the shaver head back on until it clicks into place.
- Attach the clipper attachment to the main body of the
REMAINING BATTERY INDICATOR
When the trimmer is on, the digital screen
shows the remaining battery power and the
battery symbol below is always on.
appliance.
- This device has 4 additional nozzles with different cut
CHARGING INDICATOR
- Flashes while charging, and stays on until
CLEANING THE NOSE AND EAR TRIMMER
Clean the nose trimmer head with a brush. Please place
the body of the instrument and its accessories in the stand
after cleaning to avoid damage to the instrument or loss of
accessories.
lengths (3, 6, 9, 12 mm). Install the attachment you need.
- Press the power button.
- You can start cutting.
the charge reaches 100 %.
- Blinks when the charge drops to 5 % to
remind you to recharge the device.
RAZOR HEAD
6. SPECIFICAIONS
- Attach the shaver head to the main body of the appliance.
- Press the power button.
- You can start shaving. (Note: The razor head is for use on
- Input voltage / current: 5 V
1 А
- Power: 3 W
- Power supply: battery Li-Ion, 600 mAh,
1,2 V
0,6 А
- Full charge time: 90 minutes
ATTENTION! Do not use this appliance near water.
BLADE LUBRICATION INDICATOR
For up to 30 minutes of use, this indicator
will flash every 0.5 seconds to remind you
that the blade needs to be lubricated. And the
indication will disappear when the device is
restarted.
the face or neck only.)
NOTE: Do not press the attachment too hard against your skin
while shaving - this may damage the shaver foil or harm your
skin (for example, burning sensation, numbness or pain).
13