Текст страницы
English
Belt Hook (Fig. C)
Included with Some Models
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook for
tethering or securing the tool to a person or object during
use. DO NOT suspend tool overhead or suspend objects
from the belt hook.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
These drills/drivers are professional power tools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing a belt hook, use only
the screw that is provided. Be sure to securely tighten the screw.
A belt hook 15 can be be attached to either side of the tool
using only the screw 16 provided, to accommodate left- or
right‑handed users. If the belt hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw 16 that holds it in
place then reassemble on the opposite side. Be sure to securely
tighten the screw.
WARNING: Use only DeWALT battery packs and chargers.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Installing and Removing Attachments (Fig. A, D)
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack 1 is fully charged.
To Install the Battery Pack into the Tool Handle
WARNING: Shock hazard. Under no circumstances should this product be used near water.
1. Align the battery pack 1 with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
WARNING: Burn hazard. Moving parts within the
power unit become hot during use. Avoid contact with
moving parts within power unit when removing and
installing accessories.
To Remove the Battery Pack from the Tool
1. Press the release button 2 and firmly pull the battery pack
WARNING: Before assembly, lock the power unit by
setting the forward/reverse slider to the center position
and remove the battery from the tool. Remove any
accessory from the attachment before removing or
installing the attachment.
1. Pull back on the locking sleeve 18 on the attachment in the
out of the tool handle.
2. Insert battery pack into the charger as described in the
direction of the arrow.
2. Slide the attachment onto the spindle 19 , aligning the
charger section of this manual.
slots 20 on the attachment with the lugs 21 around
the spindle.
NOTE: Once on the spindle you may have to rotate the
attachment a small bit side to side so the slots align with
the lugs. The 10 mm chuck attachment 8 does not have
any slots to align.
3. To remove the attachment, pull back on the locking sleeve
Fuel Gauge Battery Packs (Fig. B)
Some DeWALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 13 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
in the direction of the arrow and remove the attachment
from the spindle.
NOTE: The 6.35 mm hex right angle attachment 9 allows
additional attchments to be installed on its spindle. With
the 6.35 mm hex right angle attachment installed on the
tool follow instruction 1 and 2 of this section to install
additional attachments.
NOTE: Only use attachments that are specifically designed
for and compatible with the power unit. Refer to individual
attachment instruction manuals for specific safety warnings and
operating instructions before operating attachments with the
power unit.
10