Текст страницы
pack into power tools that have the switch in acci
dents.
power tool, if they are not supervised or instructed
about use of the power tool by a person responsible
for their safety.
•• Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for which
it was designed.
•• Do not open the battery. Danger of circuit.
•• In case of damage and improper use of the bat
tery, vapors may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapors can irritate the respiratory system.
•• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
•• When the battery is defective, liquid can escape
and come into contact with adjacent components.
Check any parts concerned. Clean such parts or re
place them, if required.
•• Protect the battery against heat, e.g., also
against continuous sun irradiation and fire. There
is danger of explosion.
•• Disconnect the plug from the power source
and / or the battery pack from the power tool before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
WARNING! Read all safety warnings and
all instructions.
•• Store idle power tools out of the reach of chil
dren and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
•• Protect the battery charger from rain and mois
ture. The penetration of water in a battery charger in
creases the risk of electric shock.
•• Do not charge other batteries. The battery charger
is suitable only for charging lithium ion batteries within
the listed voltage range. Otherwise there is danger of
fire and explosion.
•• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's op
eration. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
•• Keep the battery charger clean. Contamination
may cause the danger of electric shock.
•• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
•• Check the battery charger, cable and plug each
time before using. Do not use the battery charger
when defects are detected. Do not open the battery
charger yourself and have it repaired only by quali
fied personnel using original spare parts. Damaged
battery chargers, cables and plugs increase the risk of
electric shock.
•• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazard
ous situation.
•• Do not operate the battery charger on easily in
flammable surfaces (e.g. , paper , textiles , etc.) or
in combustible environments. There is danger of fire
due to the heating of the battery charger during charging.
•• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
Service
•• Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool. Therefore, proper
holding can reduce the risk of accidents or injuries.
•• Have your power tool serviced by a qualified re
pair person using only identical replacement parts.
This will ensure that the safety of the power tool is main
tained.
Battery tool use and care
•• Follow instruction for lubricating and changing ac
cessories.
Special safety warnings
•• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
•• Use power tools only with specifically designat
ed battery packs. Use of any other battery packs may
create a risk of injury and fire.
Safety warnings common for grinding, sanding,
wire brushing, polishing or abrasive cutting-off
operations:
•• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
•• This power tool is intended to function as a
grinder, sander, wire brush, polisher or cut-off tool.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and / or serious injury.
•• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
•• Operations such as grinding, sanding, wire
brushing, polishing or cutting-off are not recom
mended to be performed with this power tool. Op
erations for which the power tool was not designed may
create a hazard and cause personal injury.
•• Avoid unintentional switching on. Ensure the
on / off switch is in the off position before insert
ing battery pack. Carrying the power tool with your
finger on the on / off switch or inserting the battery
•• Do not use accessories which are not spe
cifically designed and recommended by the tool
manufacturer. Just because the accessory can be
23
English