Текст страницы
Wearing protective gloves is recom
mended for mounting / replacing acces
sories.
18 Disc *
19 Clamping nut
20 Label *
21 Indicator (red) *
22 Indicator (green) *
Mounting of cutting / grinding disc (see fig. 3)
* Optional extra
•• Install flange 17 onto spindle 16 (see fig. 3).
•• Install one of the aforementioned accessories onto
spindle 16.
Not all of the accessories illustrated or described
are included as standard delivery.
•• Press and hold spindle lock 3.
•• Screw clamping nut 19 onto spindle 16 and tight
en it with flange wrench 13. Attention: at mounting
any accessories over 4 mm thick clamping nut 19
should be turned over (see fig. 3).
Installation and regulation of power tool
elements
•• Release spindle lock 3.
Replacing the cutting / grinding disc (see fig. 3-4)
Before carrying out any works on the power tool
remove the battery 11.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
•• Press and hold spindle lock 3.
•• Release clamping nut 19 with flange wrench 13 (see
fig. 4).
•• Replace the accessory.
•• Screw clamping nut 19 onto spindle 16 and tight
en it with flange wrench 13. Attention: at mounting
any accessories over 4 mm thick clamping nut 19
should be turned over (see fig. 3).
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
•• Release spindle lock 3.
Additional handle (see fig. 1)
Charging procedure of the power tool
battery
Always use the additional handle 6 when operating.
Additional handle 6 may be positioned as deemed
comfortable by the user.
Initial operating of the power tool
•• Unscrew additional handle 6 as shown on fig. 1.
•• Screw additional handle 6 into another threaded
opening.
The power tool is supplied with a partially charged
battery 11. Before the first use, the battery 11 must
be fully charged.
Protective casing
Charging process (see fig. 5, 8)
•• Press the battery lock 10 and remove the battery 11
(see fig. 5.1, 8.1).
Always use protective casing 1 when ap
plying cutting and grinding discs. Opera
tion of the aforementioned accessories
without protective casing 1 is strictly
forbidden. Protective casing 1 should always face
the operator with its closed part.
•• Connect the charger 14 to the power supply.
•• Insert battery 11 into charger 14 (see fig. 5.2, 8.2).
•• Disconnect the charger 14 from power supply after
charging.
•• Remove the battery 11 from the charger 14 and
mount battery 11 in the power tool (see fig. 5.3, 8.3).
Adjusting the protective casing into work position
(see. fig. 2)
Charger indicators (see fig. 6, 9)
•• This power tools are supplied with the mounted pro
tective casing 1. Before proceeding to establish a pro
tective casing 1, so that its closed part facing toward
the user.
Charger indicators 21 and 22 inform of the battery 11
charging process. Signals of the indicators 21 and 22
are shown on the label 20 (see fig. 6, 9).
•• Press the locking button 15 and while holding it in
this position, turn the protective casing 1 into the re
quired position (see fig. 2.1-2.2).
•• Release locking button 15 (see fig. 2.3).
•• Fig. 6.1, 9.1 - (the green indicator 22 is on, the
battery 11 is not inserted in the charger 14) - the
charger 14 is connected to the power network (ready
for charging).
Mounting / replacement of accessories
•• Fig. 6.2, 9.2 - (the green indicator 22 is blinking, the
battery 11 is inserted in the charger 14) - the battery 11
is being charged.
•• Fig. 6.3, 9.3 - (the green indicator 22 is on, the
battery 11 is inserted in the charger 14) - the bat
tery 11 is fully charged.
After mounting accessories of any kind,
make a trial run before commencing op
eration - start the power tool and let it
work in idle mode for not less than 30
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
•• Fig. 6.4, 9.4 - (the red indicator 21 is on, the bat
tery 11 is inserted in the charger 14) - the charg
ing process of the battery 11 is terminated due to
27
English