Текст страницы
Installing or removing flex wheel
For tool with locking screw type
wheel guard
Optional accessory
WARNING: Always use supplied guard when
flex wheel is on the tool. Wheel can shatter during
use and guard helps to reduce chances of personal
injury.
Mount the wheel guard with the protrusions on the wheel guard
band aligned with the notches on the bearing box. Then rotate
the wheel guard to such an angle that it can protect the opera-
tor according to work. Be sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
► Fig.7: 1. Wheel guard 2. Bearing box 3. Screw
► Fig.14: 1. Lock nut 2. Flex wheel 3. Back up pad
4. Inner flange
For tool with clamp lever type wheel guard
Optional accessory
Follow instructions for depressed center wheel but also
use back up pad over wheel. See order of assembly on
accessories page in this manual.
Super Flange
WARNING: The wheel guard must be fitted
on the tool so that the closed side of the guard
always points toward the operator.
Optional accessory
Loosen the nut, and then pull the lever in the direction
of the arrow.
► Fig.8: 1. Nut 2. Lever
Super Flange is a special accessory for model which is
NOT equipped with a brake function.
Models with the letter F are standard-equipped with
Super Flange. Only 1/3 of efforts needed to undo lock
nut, compared with conventional type.
Installing or removing Ezynut
Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the bear-
ing box. Then rotate the wheel guard to such an angle
that it can protect the operator according to work.
► Fig.9: 1. Wheel guard 2. Bearing box
Optional accessory
► Fig.10: 1. Wheel guard
Only for tools with M14 spindle thread.
CAUTION: Do not use Ezynut with Super
Flange. Those flanges are so thick that the entire
thread cannot be retained by the spindle.
Securely tighten the nut using a spanner, and then close the
lever in direction of the arrow to fasten the wheel guard. If
the lever is too tight or too loose to fasten the wheel guard,
open the lever and then loosen or tighten the nut using the
spanner to adjust the tightening of the wheel guard band.
► Fig.11: 1. Nut 2. Lever
To remove wheel guard, follow the installation proce-
dure in reverse.
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
► Fig.15: 1. Ezynut 2. Abrasive wheel 3. Inner flange
4. Spindle
Installing or removing depressed
center wheel or flap disc
Press shaft lock firmly and tighten Ezynut by turning the
abrasive wheel clockwise as far as it turns.
► Fig.16: 1. Shaft lock
Optional accessory
To loosen the Ezynut, turn the outside ring of Ezynut
counterclockwise.
WARNING: When using a depressed center
wheel or flap disc, the wheel guard must be fitted
on the tool so that the closed side of the guard
always points toward the operator.
NOTE: Ezynut can be loosened by hand as long
as the arrow points the notch. Otherwise a lock nut
wrench is required to loosen it. Insert one pin of the
wrench into a hole and turn Ezynut counterclockwise.
► Fig.17: 1. Arrow 2. Notch
► Fig.18
Installing or removing abrasive disc
CAUTION: Make sure that the mounting part
of the inner flange fits into the inner diameter of
the depressed center wheel / flap disc perfectly.
Mounting the inner flange on the wrong side may
result in the dangerous vibration.
Optional accessory
► Fig.19: 1. Sanding lock nut 2. Abrasive disc
3. Rubber pad
1.
Mount the rubber pad onto the spindle.
2.
Fit the disc on the rubber pad and screw the sand-
ing lock nut onto the spindle.
Mount the inner flange onto the spindle.
Make sure to fit the dented part of the inner flange onto
the straight part at the bottom of the spindle.
Fit the wheel / disc on the inner flange and screw the lock nut
with its protrusion facing downward (facing towards the wheel).
► Fig.12: 1. Lock nut 2. Depressed center wheel
3. Inner flange 4. Mounting part
3.
Hold the spindle with the shaft lock, and securely tighten
the sanding lock nut clockwise with the lock nut wrench.
To remove the disc, follow the installation procedure in reverse.
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
► Fig.13: 1. Lock nut wrench 2. Shaft lock
NOTE: Use sander accessories specified in this man-
ual. These must be purchased separately.
To remove the wheel, follow the installation procedure in reverse.
13
ENGLISH