Текст страницы
4.80
4.100
4.120
4 Chаnnel
WE RESPECT YOUR CHOICE!
Class
D
D
D
RMS power 4 Ω
80 W x 4 CH
100 W x 4 CH
120 W x 4 CH
RMS power 2 Ω
120 W x 4 CH
150 W x 4 CH
170 W x 4 CH
RMS power 4 Ω Bridge mode
240 W x 2 CH
300 W x 2 CH
350 W x 2 CH
Congratulations on your purchase!
The AMP™ products designed, engineered and manufactured to bring you the higheɓ
level of peɑormance and quality, and will aɍord you of liɓening pleasure.
AMP™ — ENERGY OF SOUND!
Frequency response
10 Hz – 50 kHz
10 Hz – 50 kHz
10 Hz – 50 kHz
Input sensitivity
8 V – 0.25 V
8 V – 0.25 V
8 V – 0.25 V
Signal-to-noise ratio
> 90 dB
> 90 dB
> 90 dB
Specifications
All specifications subject to change without notice.
Low-pass filter
50 Hz – 8 kHz
50 Hz – 8 kHz
50 Hz – 8 kHz
Hi-pass filter
10 Hz – 8 kHz
10 Hz – 8 kHz
10 Hz – 8 kHz
1.500
1.800
1 Chаnnel Monoblock
HIGH LEVEL input
Automatic
Automatic
Automatic
Clipping indicator
+
+
+
Class
D
D
Protection system
+
+
+
RMS power 4 Ω
200 W x 1 CH
300 W x 1 CH
Operating voltage
12 V
12 V
12 V
RMS power 2 Ω
350 W x 1 CH
500 W x 1 CH
Terminal
Clamp
Clamp
Clamp
RMS power 1 Ω
500 W x 1 CH
800 W x 1 CH
Fuse
30 A x 2
35 A x 2
40 A x 2
Frequency response
10 Hz – 50 kHz
10 Hz – 50 kHz
160х85х39
180х85х39
220х85х39
Dimensions (L/W/H), mm
Input sensitivity
8 V – 0.25 V
8 V – 0.25 V
Signal-to-noise ratio
> 90 dB
> 90 dB
Low-pass filter
35 Hz – 8 kHz
35 Hz – 8 kHz
Hi-pass filter
10 Hz – 8 kHz
10 Hz – 8 kHz
General precautions
Bass boost
0 dB – 12 dB
0 dB – 12 dB
Phase shift
0° | 180°
0° | 180°
HIGH LEVEL input
+
+
Clipping indicator
+
+
Protection system
+
+
Remote Subwoofer level control
+
+
Operating voltage
12 V
12 V
Terminal
Clamp
Clamp
Fuse
30 A x 2
30 A x 3
Dimensions (L/W/H), mm
160х85х39
200х85х39
Before inɓalling and using your new amplifier, please become familiar
with all the information contained in this manual.
Please keep this manual in a safe place for future reference.
•
Do not open or attempt to repair this unit yourself. Dangerous high voltages
are present which may result in electric shock. Refer any repairs to a qualified
service technician.
•
To avoid risk of electronic shock or damage to the amplifier, do not permit
any of this equipment to become damp or wet from water or drinks. If this does occur,
immediately unplug the power wires and send the amplifier to your local dealer
or service center as soon as possible.
•
If there is smoke or any peculiar odor present during use or if there is damage
to any of the component enclosures, immediately unplug the power wire and send
the amplifier to your local dealer or service center as soon as possible.
2 Chаnnel
2.170
Class
D
RMS power 4 Ω
170 W x 2 CH
Inɓallation precautions
RMS power 2 Ω
260 W x 2 CH
RMS power 4 Ω Bridge mode
520 W x 1 CH
Frequency response
10 Hz – 50 kHz
Input sensitivity
8 V – 0.25 V
Signal-to-noise ratio
> 90 dB
Low-pass filter
50 Hz – 8 kHz
Hi-pass filter
10 Hz – 8 kHz
Band-pass filter
+
HIGH LEVEL input
+
Clipping indicator
+
Protection system
+
Remote Subwoofer level control
+
Operating voltage
12 V
Terminal
Clamp
Fuse
30 A x 2
Before you drill or cut any holes, inveɓigate your car's layout very carefully. Take special
care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring.
Never operate the amplifier when it is unmounted. Attach all audio syɓem components
securely to prevent damage, especially in an accident.
Before making or breaking power connections in your syɓem, disconnect the vehicle
battery. Confirm that your head unit or other equipment is turned oɍ while connecting
the input jacks and speaker terminals.
If you need to replace the power fuse, replace it only with a fuse identical to that supplied
with the amplifier. Using a fuse of a diɍerent type or rating may result in damage to your
audio syɓem or your amplifier which is not covered by the manufacturer's warranty.
Mounting the amplifier
1. Find a suitable location in the vehicle in which to mount the amplifier.
2. Make sure there is suɍicient air circulation around the intended mounting location.
3. Mark the location for the mounting hole screws by positioning the amplifier
where you wish to inɓall it.
Dimensions (L/W/H), mm
180х85х39
5
4