Текст страницы
CONTENTS
Connectors, indicators and controls
Connectors, indicators and controls .
.
.
.
.
.
.
.
.
3
Specifications .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4-5
General precautions
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5
+12V
Power cable (+) terminal to the battery. Do not forget to protect positive power cable
with appropriate fuse. It is vital that a fuse / circuit breaker (of at leaɓ equal value
to the one fitted on the amplifier) is placed inline with the power cable and is no fuɒher than
18" (40 cm) away from the battery.
Installation precautions
.
.
.
.
.
.
.
.
.
.
.
.
.
5
REM (Remote Turn-On)
Сonnector of remote activation of the amplifier.
Connecting the amplifier .
.
.
.
.
.
.
.
.
.
.
.
.
6
Power Wiring
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
High Level Input Wiring.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
Low Level Input Wiring .
.
.
.
.
.
.
.
.
.
.
.
.
.
8
GND (Ground)
The ground cable needs to carry the same current as the power cable. The amplifier ground
should be connected directly to the chassis of the vehicle, to bare metal
(not painted suɑace). The cable length should be kept to an absolute minimum.
It is not recommended that you connect the ground cable to the vehicles seatbelts.
Speaker Wiring.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
9-11
Troubleshooting .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
Warranty Repair
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
PRT PWR (Protection / Power LED)
When the amplifier is wired and inɓalled correctly the green LED on the front of the amplifier
will illuminate to indicate the amplifier is operating correctly. If the amplifier
is incorrectly wired or an abnormal situation (Speaker cables shoɒing / Overheating /
Amplifier fault) the red protection LED will illuminate.
РУС.
СОДЕРЖАНИЕ
CLIP (Clip indicator LED)
A power amplifier cannot deliver an output wave wider than its power supply voltage. When
you reach the limit, increasing gain may sound louder but sound will be diɓoɒed and can
even damage speakers. The clipping indicator indicates that the amplifier is not working
properly.
SPEAKERS OUTPUT
Speaker terminal connections.
Разъёмы, индикаторы, органы управления и настройки .
13
Технические характеристики .
.
.
.
.
.
.
.
.
.
14-15
LEVEL INPUT
Signal input, RCA jack. Connect this to the RCA outputs on your head unit.
Меры предосторожности .
.
.
.
.
.
.
.
.
.
.
.
15
Установка .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
15
REMOTE
Input for connection of the bass remote control.
Подключение усилителя.
.
.
.
.
.
.
.
.
.
.
.
.
16
AUTO TURN ON
High Level Input (read the manual for more information).
Подключение питания
.
.
.
.
.
.
.
.
.
.
.
.
.
17
Подключение по высокому уровню.
.
.
.
.
.
.
.
.
17
X-OVER (LPF | FULL | HPF)
Crossover operation mode. Average position for diɍerent types of speakers:
Subwoofer (LPF). Midbass / Midrange / Syɓem with DSP processor (FULL). Tweeter (HPF).
Подключение по низкому уровню
.
.
.
.
.
.
.
.
.
18
Подключение акустики .
.
.
.
.
.
.
.
.
.
.
.
19-21
Неисправности и методы их устранения
.
.
.
.
.
.
22
Гарантийные работы.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
FREQ (Crossover frequency control. LPF / HPF)
LPF — Low-pass filter (a filter that passes signals with a frequency lower than a selected
cutoɍ frequency).
HPF - High-pass filter (a filter that passes signals with a frequency higher than a selected
cutoɍ frequency).
BANDPASS
A filter that includes LPF and HPF at the same time.
SUBSONIC
It is used to adjuɓ infra-low playback frequencies. This makes it possible to prevent
mechanical failures of the subwoofer.
GAIN
Used to match the input signal of the headunit to the amplifier
(read the manual for more information).
PHASE SHIFT
Controlling the delay of the sound wave in order to synchronize the subwoofer with the reɓ
of the speakers (in-phase). No delay — 0 degrees (the subwoofer plays up (forward)),
maximum delay 180 degrees (the subwoofer plays down (back)).
BASS BOOST
This will allow you to booɓ the bass and is variable from 0 – 12 dB. Please note —
by booɓing +12 dB you are asking the amplifier to work 8 times harder.
3
2