Текст страницы
ENGLISH
••
Make sure that there is enough water in the
water tank (10).
••
Once the soleplate (11) reaches the set temper-
ature, the indicator (9) will go out and you can
start ironing.
••
After you finish ironing, set the temperature con-
trol knob (12) to the «MIN» position.
••
Pull the power plug out of the mains socket and
let the iron cool down completely.
BURST OF STEAM
The burst of steam function is useful for ironing
folds and can only be used at high ironing tempera-
tures (when the temperature control knob (12) is set
to «MAX» position).
When the burst of steam button (6) is pressed,
steam will go out of the soleplate (11) openings
intensively.
Notes: To avoid water leakage from the steam
openings, press the burst of steam button (6) with
4-5 sec. intervals.
STEAM IRONING
The iron is provided with an anti-drip valve that
stops water supply if the soleplate temperature
is too low; it prevents dripping from the soleplate
openings (11). During heating and cooling of the
iron soleplate, you will hear characteristic clicks of
the anti-drip valve opening/closing, which indicates
its normal operation.
Steam ironing is possible only if the temperature
control knob (12) is set to the position «•••» or
«MAX».
VERTICAL STEAMING
The vertical steam function can be used only at high
ironing temperatures (when the temperature control
knob (12) is set to the «MAX» position).
Hold the iron vertically at the distance of
10-30 cm from the clothes and press the burst
of steam button (6) with 4–5 second intervals,
steam will be released from the soleplate (11)
intensively.
Important information
Vertical steaming is not recommended for syn-
thetic fabrics.
••
To avoid fabric melting, do not touch it with the
iron soleplate while steaming.
••
Never steam clothes on a person as temperature
of the released steam is very high, use a clothes
hanger or a coat rack.
••
After you finish ironing, switch the iron off, wait
until it cools down completely, then open the
water inlet lid (2), turn over the iron and pour out
the remaining water.
••
Place the iron on its base (8).
••
Insert the power plug into the mains socket.
••
Make sure that there is enough water in the
water tank (10).
••
Set the control knob (12) to the required ironing
temperature in the steam operation zone, the
pilot lamp (9) will light up.
••
When the soleplate (11) reaches the set tem-
perature value, the pilot lamp (9) will go out, you
can start ironing.
••
Set the necessary steam intensity with the con-
tinuous steam supply knob (3).
••
In the continuous steam supply mode, steam
will be released from the openings of the sole-
plate (11) only if the iron is in horizontal position.
To stop the steam supply, put the iron vertically
or set the knob (3) to the position «
» (steam
supply is off).
••
After you finish ironing, set the temperature
control knob (12) to the position «MIN», and the
continuous steam supply knob (3) to the posi-
tion «
» (steam supply is off).
••
Pull the power plug out of the mains socket and
let the iron cool down completely.
ATTENTION!
If steam is not supplied constantly during the oper-
ation, check whether the steam supply knob (3) is
set properly and whether there is water in the water
tank (10).
WATER SPRAY
AUTOMATIC SWITCH OFF
This model has 2 automatic switching off modes.
1. If the iron remains still for 30 seconds in horizon-
tal position, there will be a sound signal, the iron
heating element will be switched off and the indi-
cator (5) will be flashing.
2. If the iron is set to the vertical position on its
base (8) and remains still for 8 minutes, there
will be a sound signal, the iron heating element
will be switched off and the indicator (5) will be
flashing.
••
To resume ironing set the iron from horizon-
tal position to vertical or vice versa, wait until
the iron soleplate (11) heats up and continue
ironing.
••
You can dampen the fabric by pressing the water
spray button (4) several times.
5
IM VT-8313.indd 5
4/24/18 10:42 AM