Текст страницы
ENGLISH
••
Pull the power plug out of the mains socket and
let the iron cool down completely.
Notes: If the steam iron has been used for a long
time without water and is very hot, do not fill the
tank with water until the iron has cooled down.
STEAM IRONING
SCALE PROTECTION SYSTEM
A special polymer filter inside the water tank softens
the water and prevents scaling on the soleplate. The
polymer filter is installed by the manufacturer and
doesn’t require replacement.
Note:
– Use tap water only. Distilled and/or deminer
alized water reduces the effectiveness of the
«Zero-Calc» anti-scale system by changing its
physico-chemical characteristics.
– Do not use chemical additives, fragrances or
descaling agents. Failure to follow the above
rules will make the warranty nil and void.
SETTING THE IRONING TEMPERATURE
••
Place the iron on its base (9).
••
Insert the power plug into the mains socket.
••
Turn the control knob (11) to set the required
ironing temperature: «•», «••», «•••» or
«MAX», depending on the type of fabric, the
indicator (7) will light up.
••
Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go
out and you can start ironing.
Note:
– If you are ironing at high temperature but you
need to switch to lower temperature, wait until
the soleplate temperature decreases and the
indicator (7) lights up, and only then you may
start ironing.
– If the item label is marked with the symbol
,
do not iron the item.
WATER SPRAY
••
Place the iron on its base (9).
••
Set the continuous steam supply knob (3) to the
utmost left position (steam supply is off).
••
Insert the power plug into the socket.
••
Make sure that there is enough water in the
water tank (10).
••
Turn the control knob (11) to set the ironing tem
perature «•••», «МАХ», the indicator (7) will
light up.
••
When the soleplate (13) reaches the set tem
perature, the indicator (7) will go out, you can
start ironing.
••
Set the steam supply with the switch (3). To do
this, set it to the middle or utmost right position
for maximal steam supply. Steam will start out
going from the soleplate (13) openings.
••
After you finish ironing, set the temperature
control knob (11) to the «OFF» position and the
steam supply knob (3) to the utmost left position
(the steam supply is off).
••
Pull the power cord plug out of the mains socket
and let the iron cool down completely.
ATTENTION!
If the steam is not constantly supplied during oper
ation, check whether the temperature control knob
(11) is set properly and there is water in the water
tank (10).
••
You can dampen the fabric by pressing the water
spray button (5) several times.
••
Make sure that there is enough water in the
water tank (10).
DRY IRONING
STEAM FLOW
This function is useful for ironing folds and can only
be used at high ironing temperatures when the
iron temperature control knob (11) is set to «MAX»
position.
••
Set the steam supply switch (3) to the utmost
left position.
••
When you press the burst of steam button (4),
the steam will be released from the soleplate
with high intensity.
Notes: To avoid water leakage from the steam
openings do not press the burst of steam button
(4) for more than 5 seconds after the heating indi
cator goes out.
••
Place the iron on its base (9).
••
Insert the power plug into the mains socket.
••
Set the continuous steam supply knob (3) to the
utmost left position.
••
Turn the control knob (11) to set the required
ironing temperature: «•», «••», «•••» or
«MAX», depending on the type of fabric, the
indicator (7) will light up.
••
Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go
out and you can start ironing.
••
After you finish ironing, set the temperature con
trol knob (11) to the «OFF» position.
ANTI-DRIP SYSTEM
If you are ironing delicate fabrics at low tempera
tures and the temperature setting you have chosen
11