Текст страницы
Cordless Impact Driver
►Comply with the requirements of local leg-
islation on battery unit recycling.
Safety warnings for impact
wrenche
►Hold the power tool by insulated grip-
ping surfaces,when performing an op-
eration where the fastener may contact
hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts
of the power tool “live” and could give the
operator an electric shock.
►Use suitable detectors to determine if
there are hidden supply lines or contact
the local utility company for assistance.
Contact with electric cables can cause fire
and electric shock. Damaging gas lines
can lead to explosion. Breaking water
pipes causes property damage.
►Hold the power tool securely. When
tightening and loosening screws be pre-
pared for temporarily high torque reac -
tions.
►Secure the workpiece. A workpiece
clamped with clamping devices or in a vice
is held more secure than by hand.
►Always wait until the power tool has
come to a complete stop before placing
it down. The application tool can jam and
cause you to lose control of the power tool.
►In the process of operation it is possible to
heat the individual parts of the product and
the replacement tool. If necessary, wait for
it to cool down or use protective gloves.
►The product operates in shock mode and
is a source of vibration. In order to avoid
damage to health, take breaks and limit
the time of work with the product.
Product description and specifi-
cations
Read all safety warnings and all in-
structions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious injury.
Intended use
The machine is intended for driving in and
loosening screws and bolts as well as for
tightening and loosening nuts within the re-
spective range of dimension.
Product features
The numbering of the product features refers
to the illustration of the machine on the graph-
ics page.
1. Tool holder
2. Locking sleeve
(2) do not store the battery unit in the contain-
er together with other metal objects such as
nails, COINS, etc.
(3) do not let water or rain fall on the battery
unit. Closing the battery unit contacts between
each other can lead to high current, overheat-
ing, possible burns and even breakage of the
unit.
►Do not store the tool and battery unit in
places where the temperature may reach
or exceed 50 c (122 f).
►Do not throw the battery unit into the fire
even if it is severely damaged or com -
pletely out of service The battery unit can
explode under fire.
►Gas may be released in case of battery
damage and improper use. Provide fresh
air and consult a doctor if you have any
complaints. Gases can irritate the respira-
tory tract.
►Clean the battery vents from time to time
with a soft, dry and clean brush.
►Charge the battery unit without fully dis-
charging Be sure to stop working with the
tool and load the unit if you notice a de -
crease in tool power.
►Never charge a fully charged battery unit.
Recharging reduces battery life.
►Charge the battery unit at room tempera-
ture Before charging the hot battery unit,
let it cool down.
►Charge the lithium-ion battery unit if you
do not use the tool for a long time (more
than six months).
►D do not open the battery and there is a
risk of short circuit
►Protect the battery from high temperatures,
such as prolonged sun heating, fire, water
and moisture There’s a risk of explosion.
►Store the battery between 0 and 45 c Do
not leave the battery in the car during the
summer.
►The lithium-ion batteries included in the kit
shall be operated in accordance with the
requirements of the dangerous goods leg-
islation.
For commercial transport, such as by a third
party or freight forwarder, special warnings
and markings should be affixed to the pack-
age. When preparing the device for shipment,
be sure to consult a specialist in hazardous
materials. Also comply with local requirements
and regulations. They can be tougher.
Close or fasten the opened contacts and pack
the battery so that it does not move around
the packaging.
5