Текст страницы
TV DIMENSIONS (DIAGRAM 1)
7. (optional) After fastening the feet to the TV housing insert the rubber washers
TV CONNECTORS
FOR MODELS CT-TV0021-32 QLED
from the accessory set into the respective openings in the bottom part of the
feet.
CT-
TV0021-32
CT-
TV0021-40
CT-
TV0021-43
CT-
TV0021-50
CT-
TV0021-55
Model
QLED
QLED
QLED
QLED
QLED
Size without
719х
892х
955х
1111х
1226х
stand (mm)
423
509
555
643
712
Mounting the TV to a wall
1. Carefully lay the TV on a table covered with soft fabric to avoid scratches.
2. Use a screwdriver to remove the screws fastening the stand/feet. Remove the
FOR MODELS CT-TV0021-40 QLED, CT-TV0021-43 QLED
Size with stand
892х
955х
1111х
1226х
stand/feet. Be careful to avoid damaging the parts.
3. Set up the wall mount so that it can be fastened to the wall as shown in
(mm)
719х
484
571
617
704
774
Figures 3 and 4.
4. Drill 4 holes in the wall (the scale is shown for reference) and screw in the
A (mm)
719
892
955
1111
1226
FOR MODELS CT-TV0021-50 QLED, CT-TV0021-55 QLED
B (mm)
484
571
617
704
774
4 anchor bolts.
5. Use a screwdriver to screw in the bolts on the back side of the TV as shown in
Fig 4. Place the TV on the wall.
C (mm)
423
509
555
643
712
D (mm)
80
84
84
66
65
E (mm)
47
49
48
33
39
F (mm)
208
237
267
268
268
G (mm)
688
848
887
1107
1117
NOTE:
1. The TV wall mount complies with the VESA standard.
2. The use of the wall mount is optional.
3. There should be no other objects on or near the wall when mounting the TV.
4. The TV should be mounted to the wall by a skilled technician.
5. Observe the assembly instruction when mounting the TV.
6. The pictures are shown for reference.
H (mm)
75
76
77
75
78
I (mm)
100
200
200
200
200
J (mm)
100
200
200
200
200
Wall mount
4. STARTING OPERTION
FRONT PANEL OF THE TV
Please carefully read the relevant sections “Important Notices and Warnings” and
“Safety Precautions” before operating the appliance.
Wall
RJ 45 – LAN RJ-45 local area network connection port. Use a LAN cable with
RJ-45 connector (not included).
OPTICAL - used for connecting audio systems with optical audio input. When
connecting an audio system that is not compatible with ARC using an HDMI cable,
you need to connect an optical audio cable to the DIGITAL AUDIO OUT (OPTICAL)
jack to output digital audio.
HDMI - input for HDMI. Ability to connect an external audio system via HDMI Audio
Return Channel (ARC) for HDMI1 input only.
USB – port for connecting USB 2.0 type devices (operates in “Media player” mode).
ANT1 – antenna connection port (75 Ohm).
ANT2 (SATELLITE) – satellite antenna connection port.
DIGITAL AUDIO OUT – coaxial digital audio outlet.
AV – TV inlet connections for left/right audio channels from different sources with
a composite intake signal connected.
COMMON INTERFACE – slot for CAM module connection.
EARPHONE – headphone connection port.
INPUT VIDEO L/R - input connectors for connecting left/right audio channels of
various external sources with a composite external signal.
– Power ON/OFF button.
Wall
STARTING OPERATION
Using the Remote Control
- Pint the RC unit towards the RC sensor located on the TV. The RC may not work
Anchor bolt
if is some object located between it and the RC sensor on the TV.
- The RC may not work properly if the TV is operated in a brightly lit room.
- The maximum effective range for proper operation of the RC unit is
approximately 7 meters.
Remote control sensor / Power indicator
Replacing RC Batteries
Replace depleted batteries without delay. Install the batteries according to
instructions to ensure proper operation of the RC unit.
31