Текст страницы
ENGLISH
Note: You can put the foodstuffs into the
cup (10).
ATTENTION!
While processing products keep the unit
vertically.
– To switch the unit on, press and hold down
the button (3).
– Use this operation mode for combined pro
cessing of liquid and solid foodstuffs.
Notes:
– Products should be put into the bowl before
••
To switch the unit on, press and hold down
the button (3).
••
After you finish using the unit, take the
power plug out of the mains socket, discon
nect the whisk gear (8) from the motor unit
(2) by turning the gear (8) counterclock
wise (pic. 3).
••
Remove the whisk (9) from the gear (8)
(pic. 2).
ATTENTION!
– Do not use the whisk attachment (9) to
knead tight dough.
– Put products into the bowl before switching
the unit on.
the unit is switched on. The amount of prod
ucts to be processed should not exceed 2/3
of the capacity of the bowl in which they are
processed.
– Before starting to chop/mix, we recommend
to peel fruit, remove inedible parts, such
as stones, and cut fruit into cubes approxi
mately 2х2 cm in size.
– After you finish using the unit, take the power
USING THE CHOPPER
The chopper is used to chop meat, cheese,
onion, herbs, garlic, carrots, walnuts, almonds,
prunes, vegetables and fruit.
ATTENTION!
Do not chop very hard products, such as ice
cubes, frozen products, nutmegs, coffee
beans, cereals etc.
plug out of the mains socket and remove the
detachable blender attachment (1), turning
it counterclockwise (pic. 1).
ATTENTION!
– Do not remove the blender attachment (1)
Before you start chopping:
– Cut meat, cheese, onions, vegetables or
during operation.
– To avoid damaging the blades, do not pro
fruit into pieces approximately 2x2 cm in
size.
– Remove stems of herbs, shell nuts.
– Remove bones, sinews and cartilage from
cess too hard products such as cereals,
rice, spices, coffee beans, hard cheeses,
frozen products etc.
– If the foodstuffs are hard to chop with the
meat.
blender attachment (1), add some liquid if
possible.
Chopping
Caution: the blades of the chopping knife (7)
are very sharp!
Always hold the chopping knife (7) by the upper
plastic end.
USING THE WHISK ATTACHMENT
Use the whisk attachment (9) only for beating
cream and egg whites, making biscuit dough or
for mixing ready desserts.
WARNING: Before installing the whisk (9) and
the gear (8), make sure that the power plug is
not inserted into the mains socket.
••
Place the chopper bowl (6) on a flat stable
surface.
••
Set the chopping knife (7) on the axis inside
the chopper bowl (6).
••
Put the products into the chopper bowl (6).
Note: Do not switch the unit on when the chop
per bowl (6) is empty.
••
Insert the whisk attachment (9) into the
whisk gear (8) (pic. 2).
••
Insert the whisk gear (8) into the motor
unit (2) and turn it clockwise, make sure that
the gear (8) and the whisk (9) are fixed prop
erly (pic. 3).
••
Insert the power plug into the mains socket.
••
Immerse the whisk (9) into the bowl with
food.
Note: You can put the foodstuffs into the
cup (10).
••
Place the geared lid (5) on the chopper
bowl (6) and turn it clockwise as far as it will
go (pic. 4).
••
Install the motor unit (2) on the geared
lid (5) feeding chute, turn the motor unit (2)
counterclockwise as far as it will go, make
sure that the motor unit (2) is fixed properly
(pic. 5).
5
IM VT-8526.indd 5
12/19/19 10:40 AM