Текст страницы
2. Use a screwdriver to lift up the cover of the mains
¡ The worktop into which you are fitting the appli-
ance must be able to withstand loads of approx.
60 kg.
¡ For thin worktops, use heat-resistant and moisture-
socket.
→ Fig. 9
3. Undo the fastening screw and use a screwdriver
resistant reinforcement material.
¡ Only check the evenness of the hob after it has
been installed.
to lift the hose clamp.
→ Fig. 10
4. Only connect to the mains socket as shown in the
Extractor hood
¡ The clearance between the extractor hood and the
hob must correspond at least to the clearance
specified in the installation instructions for the ex-
tractor hood.
Preparing the fitted units
1. Mark the unit cut-out in accordance with the in-
stallation diagram.
‒ Ensure that the angle of the cut surface to the
figure:
→ Fig. 11
– BN: Brown
– BU: Blue
– GN/YE: Green and yellow
– BK: Black
– GY: Grey
Note: If you implement the connection in accord-
ance with connection diagram 2L/2N, you must
change the configuration of the bridges in accord-
ance with the diagram.
5. After connecting the cable, tighten the screws on
the mains socket correctly.
6. Use the hose clamp to secure the power cord and
worktop is 90°.
→ Fig. 1
2. After making the cut-outs, remove any shavings.
3. Seal the cut surfaces with heat-resistant material.
tighten the fastening screw.
→ Fig. 12
7. Route the cables into the central area of the mains
socket. Close the cover on the socket.
8. If the power cord gets in the way of the drawer,
use the enclosed cable tie to secure the cable to
the underside of the hob.
→ Fig. 13
Ventilation
To guarantee that the appliance works correctly, the
hob must be sufficiently ventilated. The ventilation in
the lower section of the appliance requires a suffi-
cient supply of fresh air. Therefore, if required, adjust
the units for this purpose.
1. Maintain a minimum clearance between the rear
Inserting the hob
1. Adjust the hob in the front section of the built-in
of the unit and the kitchen wall.
→ Fig. 2
2. Ensure that an opening at the top of the rear of
niche.
→ Fig. 14
2. Insert the hob in the cut-out.
the unit is unobstructed.
→ Fig. 3
3. If the clearance from the back wall of the unit is
→ Fig. 15
3. Seal the tile joints on tiled work surfaces with silic-
less than 20 mm, create an opening on the under-
side.
→ Fig. 4
4. If the inside of the unit is not wider than 750 mm,
one rubber.
Note: Do not kink or trap the connection cable, and
keep it away from sharp edges and hot parts.
Connecting the appliance
Requirement: Observe the connection data on the
rating plate.
1. Only connect as shown in the circuit diagram:
make cuts on the side panels.
→ Fig. 5
5. Do not hermetically seal the lower base.
Note: If the appliance is installed in an island unit or
in another location that is not described here, guar-
antee that the hob is ventilated appropriately.
Installation above a drawer
¡ In order to guarantee good ventilation, the clear-
ance between the surface of the worktop and the
upper area of the drawer must be 65 mm.
→ Fig. 6
Installation above an oven
¡ To ensure good ventilation, the clearance between
→ Fig. 16 , → Fig. 17
– BN: Brown
– BU: Blue
– GN/YE: Green and yellow
– BK: Black
– GY: Grey
Note: Depending on the type of connection, you
may have to change the arrangement of the ter-
minals supplied by the factory. For this, you may
have to shorten the clamps and remove the insu-
lation in order to insert a clamp that connects the
two cables.
2. Check that the appliance is ready for operation: If
the top of the worktop and the surface of the oven
front must be 30 mm and the minimum clearance
between the oven and hob must be 5 mm.
¡ If the clearance between the hob and the oven
needs to be increased, refer to the installation in-
structions for the oven.
→ Fig. 7
,
or appears on the appliance's dis-
play, the appliance is not connected correctly. Dis-
connect the appliance from the power supply and
check the power cord connection at the mains
supply.
Installing the power cord in the mains
socket
Requirement: For appliances without a preinstalled
power supply.
Special combinations
If you install the hob above an oven made by an-
other brand, use a wooden partition floor.
→ Fig. 18
1. Turn the hob over and put it down on the base of
the packaging, a cloth or another surface in order
to prevent scratches.
→ Fig. 8
9