Текст страницы
2. PACKAGE CONTENTS
– Refrigerator - 1 pc.
– User manual - 1 pc.
– Glass shelf - 5 pcs.
– Door shelf - 6 pcs.
– Freezer container - 3 pcs.
– Container of the refrigerating chamber - 2 pc.
– Form for ice - 1 pc.
– Tray for eggs - 1 pc.
– Fastening for a door – 2 pcs.
the hinge as shown in the figure below and install him to the
opposite side.
– Install the freezer door on the bottom hinge.
– Use a screwdriver to install the middle hinge on the same side
as the bottom loop.
– Place the upper door on the middle hinge. Connect display
power cable.
– Use a screwdriver to install the top hinge, on the same side
as the rest.
– Place a cap on top of the hinge.
APPLIANCE DESCRIPTION
1. LED-lamp
2. Refrigerator shelves
3. Freshness zone
4. Freezer containers
5. Adjustable feet
6. Door shelves
VENTILATION
The compressor and condenser of the refrigerator heat up during
operation, so it is necessary to provide sufficient ventilation to
the device.
– The refrigerator should be installed in a well-ventilated room
with normal humidity. It is forbidden to install a refrigerator
in rooms with high humidity, for example, in bathrooms,
basements.
– When installing, ensure minimum gaps (3-5 cm) on the sides of
the device and 10 cm on top for free air circulation. Do not block
the air movement at the back of the appliance.
– Do not place near heat sources.
– Do not place the refrigerator in direct sunlight or near heat
sources (kitchen stoves, ovens, fireplaces).
ALIGNMENT
For the efficient operation of the refrigerator, it is important that
it is on a flat surface. After installing the refrigerator in place,
adjust its position by rotating the adjustment supports in its front
part. The tilt of the refrigerator back should not exceed 5°.
3. REFRIGERATOR TRANSPORTATION
When transporting or carrying the device, hold it by the bottom
and carry it in an upright position. Do not tilt the refrigerator more
than 450 degrees. Never turn it upside down. Do not place the
appliance on the sides or back. Do not transport the device if it is
lying on its side, on the back or on the front sides. Do not use the
door as a carrying aid. This can disable the device. The two rear
legs of the refrigerator are equipped with rollers. To move around
the kitchen and accurately install the appliance in place, tilt the
refrigerator slightly in the direction of the back wall and move it.
The two front legs of the refrigerator can be adjusted in height. In
order to align the device precisely, twist the front legs to the left
or right so that the device is securely on the floor.
After transporting and installing the refrigerator, wait about
three hours before connecting it to the mains to be sure that the
refrigerant has been properly distributed after transportation -
this is necessary for the refrigerator to work properly.
4. INSTALLING THE REFRIGERATOR
Proper installation is necessary to ensure reliable and efficient
operation of the refrigerator. It is necessary to lift the refrigerator
by holding it by the bottom. Do not pull on the door or handle.
The manufacturer’s warranty does not cover damage to the
door as a result of its rearrangement. Repairs caused by such
circumstances will be carried out at the expense of the owner.
CONNECTION TO THE POWER SUPPLY
The refrigerator corresponds to the 1st class of protection against
electric shock and is connected to the electrical supply using a
two-pole outlet with a grounding contact.
– Before connecting to the mains, make sure that:
– The mains voltage corresponds to the data indicated on the
special plate on the back of the refrigerator;
– The grounding contact of the electrical outlet is connected to
the grounding wire of the power supply cable of the electrical
network (the connecting wire must be designed for a current
of at least 10 A);
– The socket and plug are of the same type; if the plug does
not fit into the outlet, the outlet should be replaced with the
corresponding plug of the power cord (the work must be
performed by a qualified electrician).
The refrigerator must be installed in such a way that you always
have access to an outlet. A refrigerator connected in violation
of the safety requirements of high-power household appliances
described in this manual is potentially dangerous.
The manufacturer is not responsible for damage to health and
property if it is caused by non-compliance with the specified
installation standards.
OVERHANGING DOORS
ATTENTION!
For rearranging the door, it is recommended to contact a qualified
specialist. If you decide to reinstall the refrigerator door yourself,
use the recommendations listed below in this manual.
Tools required: Philips screwdriver, flat screwdriver, Allen key.
– Remove the cap from the top hinge.
– Remove the top loop. Disconnect the power cable of the
displaying.
– Open the top door and carefully lift it up. The door should come
off the hinge and completely disengage from refrigerator.
– Use a screwdriver to remove the middle hinge.
– Remove the freezer door.
– Use a screwdriver to remove the hinge on the bottom
refrigerator parts. Turn over the hinge mount and reinstall
5. REFRIGERATOR OPERATION
BEFORE SWITCHING ON
It is necessary to connect the refrigerator to the mains three
hours after its installation. Thus, the refrigerant will be
distributed properly after transportation – this is necessary for
the proper operation of the refrigerator.
26