Текст страницы
4. For 2 N, observe the following figure.
→ Fig. 51
5. For 1 N, observe the following figure.
→ Fig. 52
Connecting the exhaust air pipe
1. Secure the exhaust air pipe to the flat duct bend.
2. Establish the connection to the exhaust air open-
ing.
3. Seal the joints appropriately.
Switching the display for air extraction
mode
1. If required for the air extraction mode and the air
recirculation mode, change the display of the elec-
tronic control in the basic settings.
2. Observe the basic settings section in the instruc-
tion manual.
Removing the appliance
ATTENTION!
Tools may damage the appliance frame.
▶Do not prise out the appliance from above.
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
1. Observe the filters' air flow direction.
2. Insert two of the filters into the left and right of the
appliance, and slide them forwards.
→ Fig. 43
3. Insert the other filters into the left and right of the
appliance.
→ Fig. 44
Inserting grease filters
▶Insert the grease filter.
→ Fig. 45
1. Disconnect the appliance from the power supply.
2. Remove the exhaust air duct or undo the circulat-
ing-air connections.
3. Push out the appliance from below.
fr
Contenu de la livraison
Après avoir déballé le produit, inspectez toutes les
pièces pour détecter d’éventuels dégâts dus au
transport et pour vous assurer de l'intégralité de la li-
vraison.
→ Fig. 1
Code QR vidéo concernant l'installation
Vous trouverez ici le code QR pour la vidéo concer-
nant l'installation.
→ Fig. 2
Dimensions de l’appareil
Vous trouverez ici les dimensions de l'appareil
→ Fig. 3
Establishing the connection to the power
supply
1. Observe the connection data on the rating plate.
2. For 3 N, connect the cable to the mains socket in
accordance with the figure.
→ Fig. 46
3. For 2 N, connect the cable to the mains socket in
accordance with the figure.
→ Fig. 47
4. For 1 N, connect the cable to the mains socket in
accordance with the figure.
→ Fig. 48
5. For 2 L/2 N, connect the cable to the mains
socket in accordance with the figure.
→ Fig. 49
6. Note the colours of the cables.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
7. If required, arrange the supplied wire end ferrules
differently depending on the type of connection.
8. To connect two cables, if required, use a wire end
ferrule.
Cotes d'encastrement coudes de conduit
plat
Vous trouverez ici une vue d'ensemble des cotes
d'encastrement des coudes de conduit plat.
Vue latérale :
→ Fig. 4 , → Fig. 5 , → Fig. 6
Vue de face :
→ Fig. 7
‒ Shorten the wires.
‒ Remove the insulation.
Variantes d'installation
Vous trouverez ici une vue d'ensemble des diffé-
rentes variantes d'installation.
Filtre anti-odeurs et adaptateur pour mode
recirculation de l'air :
→ Fig. 8
Checking the function
1. Switch on the appliance.
2. If
,
or lights up, the appliance is not
connected correctly. → "Checking and correcting
the electrical connection", Page 23
3. If no faults appear in the appliance's display, use
the operating instructions to check that the ventila-
tion is working.
Filtre anti-odeurs, diffuseur et joint pour le mode
recirculation de l'air :
→ Fig. 9
Filtre acoustique et joint pour le mode évacuation
extérieure :
→ Fig. 10
Remarque : Vous pouvez vous procurer des
conduits adaptés à l'installation auprès du service
après-vente, sur notre site Web ou auprès de reven-
deurs spécialisés.
Checking and correcting the electrical connection
1. Disconnect the appliance from the power supply.
2. Check whether the connection to the appliance
(fig. 4) and the building-side connection (fig. 8)
correspond to the connection diagram in these in-
stallation instructions. → "Preparing the electrical
connection", Page 20 → "Establishing the connec-
tion to the power supply", Page 23
3. For 3 N, observe the following figure.
→ Fig. 50
23