Текст страницы
5. Align the template to the centre line of the back
panel of the unit and to the lower edge of the
work surface.
6. Use the template to make the cut-out in the back
panel.
7. After making the cut-outs, remove any shavings.
8. Seal the cut surfaces so that they are heat-resist-
ant and waterproof.
→ Fig. 25
Ventilation
1. In circulating-air mode, establish an air outlet in
the unit's plinth.
6. Seal the cut surfaces so that they are heat-resist-
ant and waterproof.
→ Fig. 25
Installing the appliance for air recirculation mode
with circulating-air duct
1. For circulating-air mode, use the seal, the circulat-
ing-air duct, the diffuser and the odour filter.
2. Observe the dimensions for the different flat duct
bends. → Page 19
Securing the seal
▶Secure the enclosed seal on the flat duct elbow at
a maximum of 5 mm from the edge.
→ Fig. 36
Inserting the flat duct elbow
▶Insert the flat duct elbow into the outlet opening
on the rear of the appliance.
→ Fig. 37
Inserting the appliance into the worktop cut-out
1. Ensure that the connection cable is connected to
the appliance.
2. Carefully insert the appliance into the worktop cut-
out.
→ Fig. 38
Establishing the pipework between the appliance and
the diffuser
1. Connect the components of the circulating-air duct
to each other.
‒ Secure the flat duct pipe connector by enga-
ging it in place.
‒ For an additional fixing, screw the flat duct pipe
connector together using 4 x PT 4x8 mm
screws for plastic.
→ Fig. 39
2. Connect the circulating-air duct to the flat duct el-
bow on the rear of the hob.
→ Fig. 40
3. Connect the diffuser to the circulating-air duct.
→ Fig. 41
‒ Provide a minimum air outlet cross-section of
approx. 400 cm².
‒ To keep the draught and noise low, ensure that
the outlet opening in the base panel is as large
as possible.
2. To guarantee that the appliance works correctly,
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
Installing an appliance featuring circulating-air mode
with adapter
Attaching the seal to the adapter
▶Attach the seal to the adapter with max. 5 mm to
the edge.
→ Fig. 29
Attaching the adapter
1. Clean and degrease the adhesive surface around
the cut-out in the unit's back panel.
2. Insert the adapter into the outlet opening on the
rear of the hob.
→ Fig. 30
3. Remove the adhesive tape's protective film from
the adapter.
→ Fig. 31
Inserting the appliance into the worktop cut-out
1. Ensure that the connection cable is connected to
the appliance.
2. Carefully insert the appliance into the worktop cut-
out.
→ Fig. 32
Securing the adapter
1. Hold the adapter at the central holder and use the
side holders to slide it towards the unit's back
panel in the base unit, then affix it.
→ Fig. 33
2. If required, also use screws to secure it.
→ Fig. 34
Preparing the unit for circulating-air mode with a
circulating-air duct
1. If required, remove the unit's back wall.
2. Observe the relevant dimensions when combining
with the flat duct elbow for the cut-out in the back
wall.
→ Fig. 35
3. In circulating-air mode, establish an air outlet in
the unit's plinth.
‒ Provide a minimum air outlet cross-section of
approx. 400 cm².
‒ To keep the draught and noise low, ensure that
the outlet opening in the base panel is as large
as possible.
4. To guarantee that the appliance works correctly,
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
5. After making the cut-outs, remove any shavings.
Preparing the unit for air extraction mode
1. If required, remove the unit's back wall.
2. Observe the relevant dimensions when combining
with a flat duct elbow for the cut-out in the back
wall.
→ Fig. 42
3. After making the cut-outs, remove any shavings.
4. Seal the cut surfaces so that they are heat-resist-
ant and waterproof.
→ Fig. 25
Install the appliance for air extraction mode
1. For air extraction mode, use the seal and the
acoustics filters.
2. Observe the instructions for the exhaust air pipe.
→ Page 21
Securing the seal
▶Secure the enclosed seal on the flat duct elbow at
a maximum of 5 mm from the edge.
→ Fig. 36
Establishing the piping
1. Insert the flat duct elbow into the outlet opening
on the rear of the appliance.
→ Fig. 37
2. If required, install additional piping elements.
Inserting the appliance into the worktop cut-out
1. Ensure that the connection cable is connected to
the appliance.
2. Carefully insert the appliance into the worktop cut-
out.
→ Fig. 38
22