Текст страницы
ATTENTION!
2. Using a cleaner, remove all solid precipita-
tion in the horizontal part of the drainage pipes,
moving with side of the siphon towards the main
pipe.
At the time of installation of the device is rec-
ommended Wear safety glasses. Loosen the nut
(1) on the top of the water trap (4) with a pipe
wrench (Fig. 3. 1). relative humidity not more
than 80%. Loosen the nut (2) on the top of the
extension pipe. Remove the extension pipe.
IF THE DISHWASHER WILL NOT BE CONNECT-
ED TO THE DISPOSER, GO TO PART 7 OF THIS
INSTRUCTION
Loosen the nut (3) at the bottom of the washing
flange.
6. CONNECTING THE DISHWASHER MA-
CHINES AND TRANSFER CONNECTION
Push the washing flange upwards through drain
hole of the sink and remove it (Fig. 3. 2).
If the sink is full of liquid it can be discharged
into the disposer through the inlet in its upper
parts. (Fig. 7. 2)
CLEAN THE WASH FAN WRAPPING PLACE
FROM THE SEALANT OR THE GARBAGE.
On all models inside the intake pipe there is par-
tition. The partition must be removed (Fig. 7. 1).
REMOVING THE PLATE / PARTITION
NOTE: It may be necessary to expand the drain
hole for installation flange fastening disposer.
Equipment for extending the drainage hole is
purchased separately.
3. DISASSEMBLY OF THE ASSEMBLY UNIT
1. Place the disposer on one side and place it
screwdriver into the connection for the dish-
washer, pushing it until it will not rest against the
partition in the end of the branch pipe.
Turn over the assembly (Fig. 4. 1) and loosen the
three fixing screws (1) The access to the ring (2).
2. With several blows of the hammer, knock out
the septum in the branch pipe (Fig. 7. 1).
Disconnect the retaining ring from the flange
with a screwdriver. Now the assembly unit can
be disassembled.
4. ATTACHING THE FIXING ASSEMBLY TO
WASHING Fig.5.1.
3. Remove the embossed partition from the
disposer bowl. If necessary to connect the dish-
washer, then it should be connected to the inlet
of the overflow outlet pipes To connect to the
overflow inlet, remove the exhaust pipe cover by
unscrewing the cover (Fig. 7. 3).
7. CONNECTING THE DISPOSER TO THE FIXING
UNIT ATTENTION!
1. Install one or two rubber gaskets (2) under the
washing flange (1). Make sure that The drainage
hole is not clogged, and set to flange washer /
gasket. In order to The flange of the sink became
in place, you need to crush it with a heavy load.
(To avoid scratches, use a towel as a lining. )
To avoid injury, follow the so that during the re-
moval and installation of a part Your body was
not under the disposer; during the installation it
is possible to drop it.
2. Put the second rubber part on the bottom of
the kitchen sink a gasket (2), a cardboard gasket
(optional) (3) and a metal support ring (4) (flat
side up).
Remove any objects from the grinding chamber
product before installing it on the sink.
3. While holding the second rubber gasket, card-
board padding (optional) and a metal support
ring, put the mounting ring (5) on the flange of
the sink so that it aligned with the support ring.
1. Install the product in such a way that provide
easy access to the restart button engine located
in the lower part of the body. Do not block this
place with any objects.
2. Place the disposer with three mounting loops
(1) into the sliding position by mounting rails (2).
(Fig. 8. 1)
4. Pressing tightly to the bottom of the sink rub-
ber gasket, cardboard gasket, support ring and
mounting ring, slide the snap ring (7) onto the
flange of the sink so that it snaps into the flange
groove.
3. Lift the disposer, insert the top end (installa-
tion gasket) in the mounting and turn the setting
ring to the right (with a wrench or adjustable pli-
ers) until the mounting loops are fixed (3) with
respect to the mounting rails (Fig. 8. 2).
5. Tighten the three fixing screws (6) to The fix-
ing assembly was tight and evenly pressed to
the sink.
5. CLEANING THE DRAIN PIPE
Make sure that all three mounting loops are
locked. Disposer is installed.
If you do not clean the drain pipe, it can clog.
1. Remove the water trap. (Fig. 6. 1)
4. Run water into the sink, then check the con-
nections for leaks.
11