Текст страницы
To switch off the device press and hold the button during 3 seconds.
Indirect measurement by Pythagoras’ Theorem
Calculation of distance by using 2 additional measurements
In order to save the battery power the device will switch off automatically
Short press the button
Laser distance meter
EN
within 180 seconds after the last operation.
Vector 30
DELIVERY PACKAGE
1. Laser distance meter – 1 pc.
2. Hand strap – 1 pc.
3. User manual – 1 pc.
4. Batteries 2 x 1.5V AAA LR03
3 times. Symbol will
PRODUCT DESCRIPTION
User manual
Reference point
It is possible to set the reference point either from the top or the bottom
end of the device.
The default reference point is the bottom end of the device.
To select the reference point press and hold the button during 2
Congratulations on your purchase of laser distance meter Vector 30
CONDTROL.
Safety instructions can be found in the end of this user manual and should
be carefully read before you use the device for the first time.
seconds. Corresponding indicator will appear on the display – or .
Display
appear on the display. Make
measurements of distance А
and В. Length of distance С will
be calculated and the result will
appear in the main line.
Distance В must be perpendicular
to distance С and cannot be
longer than distance А.
Measuring unit
To select required measuring unit (m, in, ft) press and hold the button
during 2 seconds.
Short press the button to exit the mode.
Keyboard
Calculation of distance by using 3 additional measurements
MEASUREMENTS
Single distance measurement
1
Distance D can be measured by making 3 additional measurements.
Short press the button to switch on the device. Laser beam will be
2
SAFETY REGULATIONS
The user manual should be read carefully before you use the device for
the first time. Unintended use of the device can be dangerous for human’s
health and cause serious injury. Keep this user manual. If the device is given
to somebody for temporary use, be sure to enclose user manual to it.
- Do not misuse the device.
- Do not remove warning signs and protect them from abrasion, because
they contain information about safe operation of the device.
The device belongs to laser class 2 in accordance with EN60825-1.
3
Short press the button 4 times. Symbol will appear on the
switched on automatically. Aim the laser beam at the object of measurement
4
and short press the button to make a single distance measurement.
display. Laser beam will be on. Make measurements of distances А, В and
Measurement result will appear on the display. Short press the button
С one by one.
Laser radiation!
Do not stare into beam
Class 2 laser
<1 mW 620-690nm
EN60825-1:2014
to delete the result of measurement and exit the mode.
Battery cover
After the last made measurement
Continuous measurement (tracking)
calculation result (distance D) will
Press and hold the button during 3 seconds.
appear in the main line on the
Functions of buttons
The device will take measurements one after another, showing the last
display.
Button
Short press
Long press
measured value in the main line, and the previous measured value in the first
Short press the button to
1
line. Short press the button to stop measuring. Short press the
Continuous
measurement (tracking)
Switch on the device/ switch on
the laser beam/single distance
measurement
exit the mode.
button to exit the mode.
- Do not look into the laser beam or its reflection, with unprotected eye or
through an optical instrument. Do not point the laser beam at people or
animals without the need. You can dazzle them.
- To protect your eyes close them or look aside.
- It is prohibited to disassemble or repair the device yourself. Entrust the
device repair to qualified personnel and use original spare parts only.
- Do not use the device in explosive environment, close to flammable
materials.
- Avoid heating the batteries to avoid the risk of explosion and electrolyte
leakage. In case of liquid contact with skin, wash it immediately with soap
and water. In case of contact with eyes, flush with clean water during 10
minutes and consult the doctor.
2
Area/volume/Pythagoras
Select measuring unit
3
Addition/subtraction
Select reference point
CALCULATIONS
Addition/subtraction
Make a measurement. Short press the button to select either addition
INTENDED USE
Laser distance meter Vector 30 is intended to measure distance, to
calculate area and volume of measured objects and perform calculations
by and Pythagoras’ Theorem. The device is suitable for use at both indoor
and outdoor building areas.
4
Delete the measurement result/exit
the mode
Switch off the device
or subtraction, and make the 2nd measurement. Calculation result will
TECHNICAL SPECIFICATIONS
Display
appear in the main line on the display. The next measurements will also be
MEASUREMENT CONDITIONS
Measurement range
The maximum measurement range is 30 m. At night, at dusk, or if the object
of measurement is shaded, the measurement range can be increased
without the use of a reflective plate. Use a reflective plate to increase the
measurement range during daylight hours, or if the object being measured
has a poor reflective surface.
Measuring range*
0,05…30 m
added/subtracted to/from the next measuring result.
Smallest unit displayed
1 mm
6
3
4
Area
Measuring accuracy **
±3 mm
Short press the button once. Symbol will appear on the
Laser
Class II, 620-690 nm, <1 mW
1. Main line for displaying
measurement/calculation
results
Object surface
When measuring up to colorless liquids (e.g. water), dust-free glass,
polystyrene or similar translucent and glossy surfaces, the measurement
results may be wrong. When measuring to very dark surfaces, the
measurement time may increase.
Continuous measurement
+
display. Laser beam will be on. Short press the button to measure
Addition/subtraction
+
the 1st side (length). Short press the button to measure the 2nd
2
2. Additional line for displaying
measurement/calculation
results
Area/volume
+
side (width). Area (composition of length and width) will be calculated and
3. Indication of the mode
Calculations by Pythagoras’ Theorem
+
appear in the main line on the display.
Automatic shutdown of the laser
30 seconds
4. Battery charge level
indication
Short press the button to exit the mode.
Automatic shutdown of the device
180 seconds
5
5. Measuring unit
Volume
Battery life
Up to 5000 measurements
Storage temperature
-20…+70 °С
Short press the button twice. Symbol will appear on the
6. Indication of the reference
point
1
Operating temperature
0…+40 °С
display. Laser beam will be on. Short press the button to measure
Dust and water protection rate
IP54
Power supply
2 х 1.5V AAA LR03 (alkaline)
the 1st side (length). Short press the button to measure the
Dimensions
115х39х19 mm
2nd side (width). Short press the button to measure the 3rd side
Weight
42 g
(height). Volume (composition of length, width and height) will be calculated
OPERATION
Insert/replace batteries
Remove the battery cover. Insert the batteries, observing correct polarity.
Put the battery cover back.
Replace the batteries as soon as the error 203 appears on the display.
Remove the batteries from the device if it’s not used for a long time to avoid
corrosion and battery discharge. All batteries must be replaced at the same
time. Both batteries must be of the same brand, with the same charge level.
and appear in the main line on the display.
* Use a target plate to increase the measurement range during daylight or
if the target has poor reflection properties.
Switch on/off
Short press the button to exit the mode.
To switch on the device short press the button . The device will
switch on and enter single distance measurement mode.
** Accuracy can decrease under unfavorable conditions, such as intense
sunshine or when measurements are made against glossy or transparent
surfaces, moving objects, objects with rough surface or when laser beam
is reflected.