Текст страницы
• Do not obstruct the ventilation grilles during operation.
no broken or worn parts.
• Only USE detergents which will not corrode the coating
materials of the high pressure hose/electrical cable
• The cross-section of any extension cables used must be
proportional to their length, i. e. the longer the extension
cable, the greater the cross-section; cables with a protec
tion level of “IPX5” must be used.
• ENSURE that all people or animals keep a minimum dis
tance of 16 yd. (15m) away.
• Position the high pressure cleaner AS NEAR POSSIBLE to
the water supply.
• Use the high pressure cleaner only with accessories and
replacement parts authorized by the manufacturer. The
use of original accessories and replacement parts will en
sure safe, trouble-free operation.
ASSEMBLY
• Connecting water hose to inlet first,and turn on the tap.
Make sure the machine is full of water. . Then turn on the
main switch. The most important thing is not forget to
press the in electronic control center to start the machine.
• Avoid unintentional firing of the trigger. Do not carry
the lance / trigger assembly with your hand over the trig
ger. Always use the trigger lock mechanism.
• The electronic control center has three pressure modes
for users to choose. There are soft, medium and strong
mode. The pressure depends upon which attachment is
best suited to the surface you are cleaning.
• Ensure that the safety lock on the trigger is used, when
you have stopped using the pressure washer to prevent
accidental operation.
• If you want to increase the pressure level, press the +
button in the electronic control center.
• If you want to reduce the pressure level, press the - but
ton in the electronic control center.
• Do not use the cleaner with inflammable or toxic liquids,
or any products which are not compatible with the correct
operation of the high pressure cleaner.
• Do not direct the water jet towards the unit itself, electri
cal parts or towards other electrical equipment.
• When you increase the pressure level to make the
pressure indicator turn red, it means that the machine is
working at the maximum pressure. At this time, please do
not let the machine work continuously for more than 15
minutes under the maximum pressure.
• Do not allow children or incompetent persons to use
the high pressure cleaner.
• Do not touch the plug and/or socket with wet hands.
PRE-OPERATION:
Adjusting fan pattern
• Do not use the high pressure cleaner if the electrical ca
ble is damaged.
• Do not use the high pressure cleaner if the high pressure
hose is damaged.
The angle of spray coming out of the lance may be adjust
ed on some lances by rotating the nozzle. This will vary the
spray pattern from approximately a 0° narrow high impact
stream to a 60° wide fan spray
• Do not jam the trigger in the operating position.
A narrow stream has high impact force on the cleaning
surface and results in maximum deep cleaning in a con
centrated area. However, this narrow high impact spray
must be used cautiously, as it may damage some surfaces.
• Check that the data plates are affixed to the high pres
sure cleaner, if not, inform your dealer. Cleaners without
plates must NOT be used as they are unidentifiable and
potentially dangerous.
• Do not tamper with or alter the calibration of the safety
valve.
A wide fan pattern will distribute the impact of the water
over a larger area, resulting in excellent cleaning action
with a reduced risk of surface damage, Large surface areas
can be cleaned more quickly using a wide fan pattern.
• Do not alter the original diameter of the spray head
nozzle.
• Do not leave the high pressure cleaner unattended.
Nozzle cleaning instructions
• Do not move the high pressure cleaner by pulling on the
electrical cable.
• All electrical conductors MUST BE PROTECTED against
the water jet.
A clogged or partially clogged nozzle can cause a signif
icant reduction of water coming out of the nozzle and
cause the unit to pulsate while spraying. To clean out the
nozzle:
• The high pressure cleaner MUST ONLY BE CONNECTED
to a correctly earthed power supply.
1. Turn off and unplug unit.
2. Turn off water supply. Relieve any pressure trapped in
the hose by squeezing trigger 2-3 times.
• The high pressure may cause materials to bounce off
surfaces at speed; therefore protective clothing and safety
goggles MUST BE WORN.
3. Separate lance from gun.
• Before doing work on the cleaner, REMOVE the plug.
4. Rotate nozzle to the narrow stream setting. This opens
up the fan blades.
• Before pressing the trigger, GRIP the gun firmly to coun
teract the recoil.
• Maintenance and/or repair of electrical components
MUST be carried out by qualified staff.
5. Using included tip cleaner, or an unfolded paper clip,
insert wire into the nozzle hole and move back and forth
until debris is dislodged.
• DISCHARGE residual pressure before disconnecting the
high pressure cleaner hose.
6. Remove additional debris by back-flushing water
through the nozzle. To do this, place end of a garden hose
(with water running) to end of nozzle for 30-60 seconds.
• Before using the high pressure cleaner, CHECK every
time that the screws are fully tightened and that there are
9