Текст страницы
How to Install
How to Use
Removing Protective Coverings
Installing the Washboard Base Extender
Adding Water to the Clean Water Tank
Omni Station
1
Before using the robot vacuum, remove the
protective strips 1 and 2 from both sides and
protective films 3, 4 and 5.
2
3
· Install the washboard base extender to the omni station
along the direction as illustrated.
· Make sure the washboard base extender is flush with
the bottom of the omni station, and the bottom surface
is even.
Power Port
- MAX -
MAX
Indicator
White: Omni station
works properly
Blinking orange:
Omni station has an
error
Maximum Water Level Mark
Water Tank Capacity: 4 L
4
5
Connecting to Power
Dust Cabinet
Dust Cabinet
Cover
Dust Cabinet
Opening
Signaling Area
Charging Contacts
Notes:
Auto-empty
Vent
Installing the Side Brush and the Mop Assembly
· Do not add water above the maximum water level mark (MAX).
· Do not add hot water to the water tank, as this may cause the tank to become deformed.
· Do not add any substance like detergents other than clean water to avoid damaging the
robot vacuum.
Front View
Rear View
Place the omni station in an appropriate area, connect
the cord set to it, and plug the cord set into an electrical
outlet.
Note: Firmly plug the connector of the cord set into the
power port of the omni station until the indicator stays
white.
Install the side brush and the mop assembly
respectively as illustrated. They are properly
installed when you hear a "click".
Connecting with the Mi Home/Xiaomi Home App
Side Brush
Disposable bag
Mop Assembly
Placing the Robot Vacuum
This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/Xiaomi Home
app to control your device, and to interact with other smart home devices.
Mop Pad Attachment Area
Disposable Bag
Handle
Scan the QR code to download and install the app. You will be
directed to the connection setup page if the app is installed
already. Or search for "Mi Home/Xiaomi Home" in the app store to
download and install it.
Open the Mi Home/Xiaomi Home app, tap on the upper right,
and then follow the instructions to add your device.
Placing the Omni Station
Mop Pad Holder
· Before use, press and hold the button on the
robot vacuum for three seconds to turn it on.
· Once the robot vacuum is on, place it onto the
omni station, and make sure the charging contacts
on the robot vacuum and the station are fully
aligned.
· The robot vacuum connects to the omni station
successfully when you hear a voice prompt for
starting charging.
C629E33F
* The app is referred to as Xiaomi Home app in Europe (except for
Russia). The name of the app displayed on your device should be
taken as the default.
Notes:
Notes:
＞1.93 m
Mop Pad
· Before the first use, it is recommended to fully charge the robot vacuum.
· If the robot vacuum cannot be turned on due to low battery level, manually place the robot
vacuum onto the omni station to charge it for a while.
· When the robot vacuum is being charged, it will automatically turn on and cannot be
turned off.
· The robot vacuum works with the Mi Home/Xiaomi Home app, and it supports Android 9.0 &
iOS 12.0 or above.
· Only 2.4 GHz Wi-Fi networks are supported.
· The version of the app might have been updated, please follow the instructions based on
the current app version.
＞0.44 m
＞0.82 m
· Place the omni station against a wall on
a flat and hard-surfaced floor, such as
a wooden or tiled floor.
· Make sure there is empty space of more
than 0.82 meters in height, more than
1.93 meters in length, and more than
0.44 meters in width. Ensure the omni
station is in an area with a good Wi-Fi
signal near an electrical outlet.
Note: The omni station is pre-installed with a disposable
bag when leaving the factory.
06
07