Текст страницы
To remove the dust collector, hold the tool handle and
pull back the tabs on the tool. Be sure to pull the tabs on
the both sides at the same time.
► Fig.9: 1. Tab
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
When installing, align the dust collector's edge with the
groove on the base.
► Fig.10: 1. Groove
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Replacing drywall saw blade
The trigger can be locked off to prevent it from being
pulled accidentally. To lock the trigger off, press the
button from the side with
marking. To unlock, press
the button from the side with
marking.
► Fig.6: 1. Lock-off button
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and/or blade
holder. Failure to do so may cause insufficient tight-
ening of the blade, resulting in a serious personal
injury.
CAUTION: Always lock the tool off when
carrying or suspending the operation.
Adjusting depth of cut
CAUTION: Do not touch the blade or the
workpiece immediately after operation. They may
be extremely hot and could burn your skin.
CAUTION: Make sure that the blade is prop-
erly secured. Insufficient tightening of the blade may
cause blade breakage or serious personal injury.
1.
Remove the dust collector.
The cutting depth corresponds with the scale on the
blade. Loosen the screw on the blade holder until the
blade can move freely. Align the scale on the blade with
the bottom line of the blade holder. Then tighten the
screws.
► Fig.7: 1. Cutting depth 2. Bottom line of the blade
holder 3. Scale on the blade
2.
Remove the bolts on the blade holder with the hex
wrench.
► Fig.11: 1. Bolts 2. Blade holder 3. Blade
The maximum cutting depth depends on the type of
the saw blade. Always use the saw blade designed for
cutting the working material.
Type of saw blade
Max. cutting depth
3.
Set a new blade as shown in the figure. Make sure
that the curved edge of the blade points forward. Fit the
protrusion of the blade holder into the slot on the blade.
► Fig.12: 1. Slot 2. Protruded portion (opposite side)
For drywall
30 mm
4.
Adjust the cutting depth then tighten the bolts.
For wood
15 mm
5.
Attach the dust collector.
LED light
Installing snap-off blade
CAUTION: Do not look in the light or see the
source of light directly.
CAUTION: Always use the snap-off blade with
designated length, width, and thickness. An inap-
propriately installed snap-off blade can be broken. A
broken blade can fly off and cause a personal injury.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the trigger.
► Fig.8: 1. Lamp
A snap-off blade can also be used with this tool. Use 3
segments of 18 mm wide snap-off blade with 0.5 mm
thickness. The maximum cutting depth is 12.5 mm
when cutting a drywall.
► Fig.13: 1. Three segments of snap-off blade
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
1.
Loosen the bolts on the blade holder. Turn the
blade holder so that its protrusion faces outward.
2.
Insert the snap-off blade so that the sharp edge
faces forward.
ASSEMBLY
3.
Secure the snap-off blade at the position where
the end of the first segment comes to the edge of blade
holder as illustrated.
► Fig.14: 1. Blade holder 2. End of the first segment
of snap-off blade 3. Allowable cutting length
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Attaching blade cap
Removing the dust collector
CAUTION: Always attach the blade cap when
tool is not used. A bare blade may cause personal
injury or damage to the blade itself.
CAUTION: Never operate the tool without the
dust collector. Dust may come into your eyes and
cause eye injury.
8
ENGLISH