Текст страницы
Electric brake
Make sure that the surface of the lock lever is parallel
to the pipe.
3.
Turn the lever to the direction of the arrow shown
in the figure.
► Fig.17: 1. Lever
This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after the switch trigger
is released, have the tool serviced at our service center.
To remove the pipe, turn the lever to the direction of the
arrow shown in the figure and pull the pipe out while
pressing down the lock lever.
► Fig.18: 1. Lever 2. Lock lever 3. Pipe
CAUTION: This brake system is not a substi-
tute for the protector. Never use the tool without
the protector. An unguarded cutting tool may result
in serious personal injury.
Installing the protector
ASSEMBLY
WARNING: Never use the tool without the
guard illustrated in place. Failure to do so can
cause serious personal injury.
CAUTION: Take care not to injure yourself on
the cutter for cutting the nylon cord.
WARNING: Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
Attach the protector to the clamp using bolts.
► Fig.19: 1. Clamp 2. Protector 3. Cutter
Installing the cutting tool
WARNING: Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Installing the handle
NOTE: The type of the cutting tool(s) supplied as
the standard accessory varies depending on the
countries. The cutting tool is not included in some
countries.
For DUR190U and DUR191U only
NOTE: Turn the tool upside down so that you can
replace the cutting tool easily.
1.
Insert the shaft of the handle into the grip. Align
the screw hole in the grip with the one in the shaft.
Tighten the screw securely.
► Fig.12: 1. Grip 2. Screw 3. Handle
Cutter blade
CAUTION: When handling a cutter blade,
always wear gloves and put the blade cover on
the blade.
2.
Place handle between handle clamp and handle holder.
Adjust the handle to an angle that provides a comfortable
working position and then secure with hex socket head bolts.
► Fig.13: 1. Hex socket head bolt 2. Handle clamp
3. Handle holder
Attaching the barrier
CAUTION: The cutter blade must be well pol-
ished, and free of cracks or breakage. If the cutter
blade hits a stone during operation, stop the tool and
check the cutter blade immediately.
For DUR190L and DUR191L (country specific)
CAUTION: Always use the cutter blade
with the diameter described in the section for
specifications.
If the barrier is included in your model, attach it to the
handle using the screw on the barrier.
► Fig.14: 1. Barrier 2. Screw
► Fig.20: 1. Nut 2. Cup 3. Clamp washer 4. Cutter
blade 5. Spindle 6. Guard 7. Spindle lock
button
CAUTION: After assembling the barrier, do
not remove it. The barrier works as a safety part
to prevent you from contacting the cutting blade
accidentally.
1.
Mount the cutter blade onto the guard so that the
arrows on the cutter blade and protector are pointing in
the same direction.
► Fig.21: 1. Arrow
Mounting the attachment pipe
For DUR191U and DUR191L only
2.
Put the clamp washer and cup onto the cutter
blade.
Mount the attachment pipe to the power unit.
3.
While holding down the spindle lock button,
tighten the nut securely by the box wrench.
► Fig.22: 1. Spindle lock button 2. Box wrench
3. Loosen 4. Tighten
1.
Turn the lever to the direction of the arrow shown
in the figure.
► Fig.15: 1. Lever
To remove the cutting blade, loosen the nut while hold-
ing down the spindle lock button.
2.
Pull up the joint cover and insert the attachment
pipe while aligning the protrusion on the pipe (cutting
tool side) with the concave portion of the joint part.
► Fig.16: 1. Lock lever 2. Joint cover 3. Pipe
20
ENGLISH