Текст страницы
Speed
indicator
Mode
Rotation speed
NOTE: During the reverse rotation, the tool operates only
for a short period of time and then automatically stops.
Cutter blade
Plastic blade
(305 mm)
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
Nylon cutting
head
Plastic blade
(255 mm)
NOTE: If you tap the reverse button while the cutting tool is still
rotating, the tool comes to stop and to be ready for reverse rotation.
High
0 - 7,000
min
-1
0 - 5,500
min
-1
Electric brake
Medium
0 - 5,500
min
-1
0 - 5,000
min
-1
This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after the switch trigger
is released, have the tool serviced at our service center.
Low
0 - 4,600
min
-1
0 - 4,600
min
-1
CAUTION: This brake system is not a substitute for
the protector. Never use the tool without the protector. An
unguarded cutting tool may result in serious personal injury.
Electronic function
Automatic Torque Drive Technology
Constant speed control
The speed control function provides the constant rota-
tion speed regardless of load conditions.
Soft start feature
When you turn on the Automatic Torque Drive
Technology (ADT), the tool runs at optimum rotation
speed and torque for the condition of grass being cut.
The tool automatically detects the cutting tool attached
and chooses a suitable rotation speed.
Soft start because of suppressed starting shock.
ASSEMBLY
To start ADT, press and hold the reverse button until the
ADT indicator turns on.
To stop ADT, press and hold the reverse button until the
ADT indicator turns off.
► Fig.11: 1. ADT indicator 2. Reverse button
Indicator
Mode
Cutting tool
Rotation
speed
3,500 - 7,000
min
-1
WARNING: Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
ADT
Cutter blade
Plastic blade
(305 mm)
3,500 - 5,500
min
-1
Nylon cutting
head
Plastic blade
(255 mm)
WARNING: Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Reverse button for debris removal
Installing the handle
For UR006G
1.
Insert the shaft of the handle into the grip. Align
the screw hole in the grip with the one in the shaft.
Tighten the screw securely.
► Fig.13: 1. Grip 2. Screw 3. Shaft
WARNING: Switch off the tool and remove
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch off and
remove the battery cartridge may result in serious
personal injury from accidental start-up.
NOTICE: Note the direction of the grip. The
screw holes will not be aligned if the grip is not
inserted in the correct direction.
2.
Adjust the handle position, and then tighten the
knob to fix the handle.
► Fig.14: 1. Knob
For UR007G
1.
Attach the upper and lower clamps on the damper.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris entan-
gled in the tool.
To reverse the rotation, tap the reverse button and pull
the switch trigger while depressing the lock-off lever
when the cutting tool is stopped. The speed indicators
and ADT indicator start blinking, and the cutting tool
rotates in reverse direction when you pull the switch
trigger.
To return to regular rotation, release the trigger and wait
until the cutting tool stops.
► Fig.12: 1. Speed indicator 2. ADT indicator
3. Reverse button
2.
Put the handle on the upper clamp and fix it with
hex socket head bolts as illustrated.
► Fig.15: 1. Hex socket head bolt 2. Handle 3. Upper
clamp 4. Damper 5. Lower clamp
21
ENGLISH