Текст страницы
1.
Put the blade cover on the cutter blade.
OPERATION
2-tooth blade
► Fig.22
Attaching the shoulder harness
3-tooth blade
► Fig.23
4-tooth blade
► Fig.24
WARNING: Be extremely careful to maintain
control of the tool at all times. Do not allow the
tool to be deflected toward you or anyone in the
work vicinity. Failure to keep control of the tool
could result in serious injury to the bystander and the
operator.
2.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
► Fig.25: 1. Nut 2. Cup 3. Clamp washer 4. Cutter
blade 5. Spindle 6. Receive washer 7. Hex
wrench
CAUTION: Always use the shoulder harness
attached to the tool. Before operation, adjust the
shoulder harness according to the user size to
prevent fatigue.
3.
Mount the cutter blade onto the receive washer
so that the arrows on the cutter blade and protector are
pointing in the same direction.
► Fig.26: 1. Arrow
CAUTION: Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
4.
Put the clamp washer and cup onto the cutter
blade and then tighten the nut securely by the box
wrench.
► Fig.27: 1. Box wrench 2. Hex wrench 3. Loosen
4. Tighten
CAUTION: When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
NOTE: Tightening torque : 20 - 30 N•m
5.
Remove the hex wrench from the gear case.
To remove the cutter blade, follow the installation proce-
dures in reverse.
If you put on the shoulder harness included in the
tool package and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is difficult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.
Nylon cutting head
For UR006G
NOTICE: Be sure to use genuine Makita nylon
cutting head.
1.
Put on the shoulder harness and fasten the
buckle.
► Fig.30
► Fig.28: 1. Nylon cutting head 2. Spindle 3. Hex
wrench 4. Loosen 5. Tighten
2.
Clasp the hook on the shoulder harness to tool's
hanger.
► Fig.31: 1. Hook 2. Hanger
1.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2.
Place the nylon cutting head onto the spindle and
tighten it securely by hand.
3.
Adjust the shoulder harness to a comfortable
working position.
► Fig.32
3.
Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Plastic blade
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle while
holding the tool to release the tool from the shoulder
harness.
► Fig.33: 1. Buckle
For UR007G
NOTICE: Be sure to use genuine Makita plastic
blade.
► Fig.29: 1. Plastic blade 2. Spindle 3. Hex wrench
4. Loosen 5. Tighten
1.
Clasp the hook on the shoulder harness to tool's
ring and hanger.
► Fig.34: 1. Ring 2. Hook 3. Hanger
1.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2.
Put on the shoulder harness on your left shoulder.
Adjust the shoulder harness to a comfortable working
position.
► Fig.35
2.
Place the plastic blade onto the spindle and
tighten it securely by hand.
3.
Remove the hex wrench from the gear case.
To remove the plastic blade, follow the installation pro-
cedures in reverse.
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle while
holding the tool to release the tool from the shoulder
harness.
► Fig.36: 1. Buckle
23
ENGLISH