Текст страницы
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
9 Mounting lug
10 Casing screw
11 Spindle
12 Flange
13 Disc *
14 Clamping nut
15 Speed selector thumbwheel
Wearing protective gloves is recom
mended for mounting / replacing acces
sories.
* Optional extra
Mounting of cutting / grinding disc (see fig. 3)
Not all of the accessories illustrated or described
are included as standard delivery.
•• Install flange 12 onto spindle 11 (see fig. 3).
•• Install one of the aforementioned accessories onto
spindle 11.
Installation and regulation of power tool
elements
•• Press and hold spindle lock 2.
•• Screw clamping nut 14 onto spindle 11 and tighten it
with flange wrench 8. Attention: at mounting any ac
cessories over 4 mm thick clamping nut 14 should
be turned over (see fig. 3).
Before carrying out any works on the power tool it
must be disconnected from the mains.
•• Release spindle lock 2.
Replacing the cutting / grinding disc (see fig. 3-4)
Do not draw up the fastening elements
too tight to avoid damaging the thread.
•• Press and hold spindle lock 2.
•• Release clamping nut 14 with flange wrench 8 (see
fig. 4).
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Additional handle (see fig. 1)
•• Replace the accessory.
•• Screw clamping nut 14 onto spindle 11 and tighten it
with flange wrench 8. Attention: at mounting any ac
cessories over 4 mm thick clamping nut 14 should
be turned over (see fig. 3).
•• Release spindle lock 2.
Always use the additional handle 5 when operating.
Additional handle 5 may be positioned as deemed
comfortable by the user.
Initial operating of the power tool
•• Unscrew additional handle 5 as shown on fig. 1.
•• Screw additional handle 5 into another threaded
opening.
Always use the correct supply voltage: the power
supply voltage must match the information quoted on
the power tool identification plate.
Protective casing
Switching the power tool on / off
Always use protective casing 4 when ap
plying cutting and grinding discs. Opera
tion of the aforementioned accessories
without protective casing 4 is strictly
forbidden. Protective casing 4 should always face
the operator with its closed part.
Mounting / dismounting the protective casing (see
fig. 2)
Switching on:
Press the back part of on / off switch 6 and while holding
it in this position, move on / off switch 6 forward. Press
the front part of on / off switch 6 to fix it in pressed
position.
Switching off:
Push the back part of on / off switch 6.
Design features of the power tool
•• With a screwdriver (not supplied with the power tool)
release casing screw 10 and install protective casing 4
onto the spindle neck, watching that mounting lug 9
comes into the longitudinal groove of the spindle neck
(see fig. 2).
Speed selector thumbwheel
[CT13502-115V, CT13502-125V]
•• Turn protective casing 4 into the required position
and tighten casing screw 10 with a screwdriver (not
supplied with the power tool).
•• When dismounting protective casing 4 repeat the
aforementioned operations in reverse order.
Mounting / replacement of accessories
Using revolution adjustment switch 15, you may se
lect the required spindle speed (also during opera
tion).
The required speed is dependent on the material and
can be determined with practical trials.
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes. To
do it, set a maximum speed and leave your power tool
to run idle.
After mounting accessories of any kind,
make a trial run before commencing op
eration - start the power tool and let it
work in idle mode for not less than 30
24
English