Текст страницы
the extraction shaft are sucked back into the living
space.
Risk of poisoning from flue gases being drawn back
in.
▶If an extractor hood with an open-flued heat pro-
duction source is installed, the power supply for
the extractor hood must be provided with a suit-
able safety switch.
Information about the electrical
connection
In order to safely connect the appliance to the elec-
trical system, follow these instructions.
▶Always ensure adequate fresh air in the room if
the appliance is being operated in exhaust air
mode at the same time as a room-air-dependent
heat-producing appliance is being operated.
▶It is only possible to safely operate the appliance
if the pressure in the room in which the heating
appliance is installed does not drop more than
4 Pa (0.04 mbar) below atmospheric pressure.
This can be achieved whenever the air needed for
combustion is able to enter through openings that
cannot be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other tech-
nical means. An incoming/exhaust air wall box
alone does not ensure compliance with the limit.
▶In any case, consult your responsible chimney
sweep. They are able to assess the house's entire
ventilation setup and will suggest the suitable
ventilation measures to you.
▶Unrestricted operation is possible if the appliance
is operated exclusively in circulating-air mode.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appli-
ance from the electricity supply. The appliance must
only be connected to a mains socket that has been
installed correctly.
▶An all-pole isolating switch must be integrated into
the permanent electrical installation in accordance
with the conditions of overvoltage category III and
in accordance with the installation regulations.
▶The permanent electrical installation must only be
wired by a professional electrician. We recom-
mend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
¡ Do not kink or trap the connection cable, and
keep it away from sharp edges.
¡ Route the connection cable in such a way that it
does not touch the hot casing.
¡ Use only the connection cable that is supplied
with the appliance or is provided by technical
after-sales service.
¡ This appliance complies with the EC interference
suppression regulations.
¡ The appliance corresponds to protection class 1.
You should therefore only use the appliance with
a protective earth connection.
¡ The manufacturer shall assume no liability for mal-
functions or damage resulting from incorrect elec-
trical wiring.
WARNING ‒ Risk of fire!
The grease deposits in the grease filter may catch
fire.
▶Never work with naked flames close to the appli-
ance (e.g. flambéing).
▶Do not install the appliance near a heat-producing
appliance for solid fuel (e.g. wood or coal) unless
a closed, non-removable cover is present. There
must be no flying sparks.
Preparing the electrical connection
Requirement: Only after-sales service staff who have
been trained accordingly may carry out work on the
inside of the appliance or replace the power cord.
WARNING ‒ Risk of injury!
Changes to the electrical or mechanical assembly
are dangerous and may lead to malfunctions.
▶Do not make any changes to the electrical or
mechanical assembly.
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
▶Wear protective gloves.
The appliance is heavy.
▶To move the appliance, two people are required.
▶Use only suitable tools and equipment.
1. Observe the information about the electrical con-
nection.
An incorrect installation, an improper installation
or connection invalidates the warranty.
2. If a longer mains power cable is required, contact
the after-sales service. Connecting cables up to
2.20 m are available.
3. On appliances without a preinstalled cable, insert
the power cable into the mains socket.
WARNING ‒ Risk of suffocation!
Children may put packaging material over their
heads or wrap themselves up in it and suffocate.
▶Keep packaging material away from children.
▶Do not let children play with packaging material.
Opening the mains socket
▶Use a screwdriver to lift the cover of the mains
outlet.
→ Fig. 15
Preparing the mains socket
1. Undo the screw.
→ Fig. 16
2. Use a screwdriver to lift the hose clamp.
→ Fig. 17
3. Undo the hose clamp.
→ Fig. 18
WARNING ‒ Risk of poisoning!
Risk of poisoning from flue gases being drawn back
in.
▶Do not emit the exhaust air into a smoke or ex-
haust gas flue that is in operation.
▶Do not emit the exhaust air into a shaft that is
used to ventilate installation rooms for heat-produ-
cing appliances.
▶If the exhaust air is to be conveyed into a smoke
or exhaust gas flue, you must obtain the consent
of the heating engineer responsible.
Connecting the cable to the mains socket
1. For 3 N, connect the cable to the mains socket in
accordance with the following figure.
→ Fig. 19
20