Текст страницы
LED lamp
Rotation to the right (drilling, screwing in) - move
the rotational direction switch 11 to the right.
When the on / off switch 10 is pushed, the LED lamp 5
is automatically switched on that allows to carry out
works in low light conditions.
Rotation to the left (unscrewing) - move the rota
tional direction switch 11 to the left.
Rotation speed stabilization system
Recommendations on the power tool op
eration
The stabilization system maintains the preset RPM
both at an idle speed and under load. This allows for
the smooth advance of the power tool during opera
tion.
Wear thick soft gloves when working to
reduce vibration impact on your body.
Safety clutch
•• Always use additional handle 4 when working, it will
ensure a better control of your power tool and reduce
recoil.
The safety clutch protects the power tool against over
load and damage in case of accessory sticking during
drilling.
Function switch (see fig. 15)
•• At impact drilling the result does not depend on the
pressing force you apply to your power tool, which is
due to the impact mechanism design. This is why do
not exert excessive pressure on your power tool, as it
may result in borer seizing and motor overload.
Switching the operation modes shall be
carried out only in the off mode of the
tool's motor.
•• In order to decrease dust production when drilling
holes in walls and ceilings, take actions indicated in
fig. 16.
Caution: drill wood and metals in the im
pactless drilling operation mode only.
Function switch 7 is fitted with lock
button 6 that is used to fix the function
switch 7 in a set position. Rotate function
switch 7 while pressing button 6 in order
to set a desired operating mode.
•• Grease the drill bit regularly when drilling holes in
metals (except drilling non-ferrous metals and their al
loys).
Function switch 7 is designed for the switching the
following operation modes of the tool:
•• When drilling hard metals, apply more force to the
power tool and lower the rotation speed.
•• When drilling large diameter holes in metal, first drill
a hole with a smaller diameter and ream it till the nec
essary diameter (see. fig. 17.1).
Drilling (set the function switch 7 in the position in
dicated in figure 15.1) - non-impact drilling in wood,
synthetics, metal.
•• In order to avoid splitting of the surface at an exit
point of a drill bit when drilling holes in wood, follow the
instructions shown in figure 17.2.
Impact drilling (set the function switch 7 in the po
sition indicated in figure 15.2) - impact drilling in ma
sonry, concrete, natural stone.
•• When drilling holes in glazed ceramic tiles, in order
to improve the drill centering accuracy and to save
the glaze from damage, apply adhesive tape to the
presumed hole center and drill after that (see fig. 18).
Caution: drill tiles in the impactless drilling opera
tion mode only.
Chisel rotation (set switch 7 in the position shown on
figure 15.3) - this mode does not allow operating your
power tool, but allows setting the chisel in a comfort
able position for chiseling works.
Chiselling (set the function switch 7 in the position in
dicated in figure 15.4) - chiselling ducts in masonry,
concrete, stone, removing ceramic tiles.
Power tool maintenance / preventive
measures
Before execution of any procedures, centre the re
verse switch 11.
In order to make switching between the
operation modes smoother, rotate slight
ly chuck 1 (SDS PLUS) by hand.
Battery maintenance instruction
Stepless speed adjustment
•• Charge timely before the battery 12 is completely
exhausted. Stop operation in low power and charge it
immediately.
•• Do not overcharge when the battery 12 is full, other
wise it will shorten the life time.
Speed is controlled from 0 to maximum by
pressing force of on / off switch 10. Weak
pressing results in low revolutions, which
enable a smooth power tool switch-on.
•• Charge battery 12 in the room temperature of 10°C
to 40°C (50°F to 104°F).
Changing the rotational directions
•• Charge battery 12 every 6 months without operation
for a long time.
•• Replace worn out batteries in time. Decline of pro
duction or a significantly shorter runtime of the power
tool after charging indicates aging of the battery 12 and
Change the direction of rotation only
after a full stop of the motor, acting oth
erwise may cause damage to the power
tool.
30
English